Self-igniting light for lifebuoy and self-activating smoke signal
1 Scope
This standard specifies the requirements, test methods, inspection rules, and marking, packaging, storage and transportation of the self-igniting light and self-activating smoke signals (hereinafter referred to as the "combined signals") for lifebuoys.
This standard is applicable to the design, manufacture and acceptance of combined signals.
This standard is also applicable to the self-activating smoke signals for lifebuoys.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document applies.
GB/T 2423.3 Environmental testing for electric and electronic products - Part 2: Testing method - Test Cab: Damp heat, steady state (GB/T 2423.3-2006, IEC 60068-2-78:2001, IDT)
GB/T 2423.17 Environmental testing for electric and electronic products - Part 2: Test methods - Test Ka: Salt mist (GB/T 2423.17-2008, IEC 60068-2-11:1981, IDT)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
self-igniting light and self-activating smoke signal
signal that is, when in use, capable of generating the indicating light and smoke by itself only by means of the automatic release device
4 Designation example
The combined signals with a continuous smoke development time of not less than 15min, and a luminous intensity of not less than 2cd and a luminous time of not less than 2h of self-igniting light are designated as follows:
Combined signal QCYD15-2-2 GB 3107-2008
5 Requirements
5.1 Appearance
5.1.1 Concise operation instructions shall be printed on the body of the combined signal.
5.1.2 The manufacturing date and expiration date shall be permanently engraved on the body of the combined signal.
5.2 Combined signal
5.2.1 Smoke color
The smoke shall be orange in color.
5.2.2 Smoke development time
The duration of smoke shall not be less than 15min.
5.2.3 Smoke concentration
After the combined signal is ignited, it shall be able to evenly and continuously eject smoke, and the smoke concentration shall not be less than 70% within at least 15min.
Foreword I
1 Scope
2 Normative references
3 Terms and definitions
4 Designation example
5 Requirements
6 Test methods
7 Inspection rules
8 Marking, packaging, storage and transportation
Bibliography
Self-igniting light for lifebuoy and self-activating smoke signal
1 Scope
This standard specifies the requirements, test methods, inspection rules, and marking, packaging, storage and transportation of the self-igniting light and self-activating smoke signals (hereinafter referred to as the "combined signals") for lifebuoys.
This standard is applicable to the design, manufacture and acceptance of combined signals.
This standard is also applicable to the self-activating smoke signals for lifebuoys.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document applies.
GB/T 2423.3 Environmental testing for electric and electronic products - Part 2: Testing method - Test Cab: Damp heat, steady state (GB/T 2423.3-2006, IEC 60068-2-78:2001, IDT)
GB/T 2423.17 Environmental testing for electric and electronic products - Part 2: Test methods - Test Ka: Salt mist (GB/T 2423.17-2008, IEC 60068-2-11:1981, IDT)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
self-igniting light and self-activating smoke signal
signal that is, when in use, capable of generating the indicating light and smoke by itself only by means of the automatic release device
4 Designation example
The combined signals with a continuous smoke development time of not less than 15min, and a luminous intensity of not less than 2cd and a luminous time of not less than 2h of self-igniting light are designated as follows:
Combined signal QCYD15-2-2 GB 3107-2008
5 Requirements
5.1 Appearance
5.1.1 Concise operation instructions shall be printed on the body of the combined signal.
5.1.2 The manufacturing date and expiration date shall be permanently engraved on the body of the combined signal.
5.2 Combined signal
5.2.1 Smoke color
The smoke shall be orange in color.
5.2.2 Smoke development time
The duration of smoke shall not be less than 15min.
5.2.3 Smoke concentration
After the combined signal is ignited, it shall be able to evenly and continuously eject smoke, and the smoke concentration shall not be less than 70% within at least 15min.
Contents of GB 3107-2008
Foreword I
1 Scope
2 Normative references
3 Terms and definitions
4 Designation example
5 Requirements
6 Test methods
7 Inspection rules
8 Marking, packaging, storage and transportation
Bibliography
