1 Scope
This Part specifies such requirements as the duty, limitation, environmental conditions, technical requirements, inspection test item and type test of the driving electrical machines and controllers of electric vehicles.
This Part applies to the driving electrical machines and controllers for electric vehicles.
All the items relevant to electrical machines which are not specified in this Part shall meet GB 755-2000. If there are special requirements, the user and manufactory may specify them in special technical agreement.
All the items relevant to driving controllers which are not specified in this Part shall meet GB/T 3859.1-1993. If there are special requirements, the user and manufactory may specify them in special technical agreement.
2 Normative References
The following documents contain provisions which, through reference in this Part of GB/T 18488, constitute provisions of this Standard. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, parties to agreements based on this Part are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies.
GB 755-2000 Rotating Electrical Machines-Rating and Performance (idt IEC 60034-1:1996)
GB/T 2423.17-1993 Basic Environmental Testing Procedures for Electric and Electronic Products Test Ka:Salt Mist (eqv IEC 60068-2-11: 1981)
GB/T 3859.1-1993 Semiconductor Convertors-Specification of Basic Requirements (eqv IEC 60146-1-1: 1991)
GB/T 4772.1-1999 Dimensions and Output Series for Rotating Electrical Machines-Part 1:Frame Numbers 56 to 400 and Flange Numbers 55 to 1080
GB/T 4942.1-2006 Degrees of Protection Provided by the Integral Design of Rotating Electrical Machines (IP Code)- Classification (IEC 60947-1: 2000,IDT)
GB/T 4942.2-1993 Degrees of Protection Provided by Enclosures for Low-voltage Apparatus (eqv. IEC 60947-1:1988)
GB/T 10068-2000 Mechanical Vibration of Certain Machines with Shaft Heights 56 mm and Higher-Measurement, Evaluation and Limits of Vibration (idt IEC idt IEC 60034-14: 1996)
GB 10069.3 Measurement of Airborne Noise Emitted by Rotating Electrical Machines and the Noise Limits-Part 3: Noise Limits (IEC 60034-9: 1997, IDT)
GB/T 12113-2003 Methods of Measurement of Touch Current and Protective Conductor Current (IEC 60990:1999, IDT)
GB/T 12665-1990 Requirements of Damp-heat Testing of Electrical Machine for Service in General Environmental Condition
GB/T 14023-2006 Vehicles Boats and Internal Combustion Engine Driven Devices-Radio Disturbance Characteristics-Limits and Methods of Measurement (CISPR 12: 2005, IDT)
GB 14711-2006 Safety Requirements of Small and Medium Size Rotating Electrical Machines
GB/T 17619-1998 Limits and methods of testing for immunity of electrical / electronic sub-assemblies in vehicles to electromagnetic radiation
GB/T 19596-2004 Terminology of Electric Vehicles (ISO 8713:2002, NEQ)
QC/T 413-2002 Basic Specification for Automotive Electrical Equipment
3 Duty and Limitation
Foreword I
1 Scope
2 Normative References
3 Duty and Limitation
4 Environmental Conditions
5 Technical Requirements
6 Inspection Test Item
7 Type Test
8 Marking, Packaging, Transportation and Storage
Appendix A (Informative) Output Capacity Matching Relation of Single Electrical Machine and Controller
Appendix B (Informative) Urban Condition and Suburb Condition
1 Scope
This Part specifies such requirements as the duty, limitation, environmental conditions, technical requirements, inspection test item and type test of the driving electrical machines and controllers of electric vehicles.
This Part applies to the driving electrical machines and controllers for electric vehicles.
All the items relevant to electrical machines which are not specified in this Part shall meet GB 755-2000. If there are special requirements, the user and manufactory may specify them in special technical agreement.
All the items relevant to driving controllers which are not specified in this Part shall meet GB/T 3859.1-1993. If there are special requirements, the user and manufactory may specify them in special technical agreement.
2 Normative References
The following documents contain provisions which, through reference in this Part of GB/T 18488, constitute provisions of this Standard. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, parties to agreements based on this Part are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies.
GB 755-2000 Rotating Electrical Machines-Rating and Performance (idt IEC 60034-1:1996)
GB/T 2423.17-1993 Basic Environmental Testing Procedures for Electric and Electronic Products Test Ka:Salt Mist (eqv IEC 60068-2-11: 1981)
GB/T 3859.1-1993 Semiconductor Convertors-Specification of Basic Requirements (eqv IEC 60146-1-1: 1991)
GB/T 4772.1-1999 Dimensions and Output Series for Rotating Electrical Machines-Part 1:Frame Numbers 56 to 400 and Flange Numbers 55 to 1080
GB/T 4942.1-2006 Degrees of Protection Provided by the Integral Design of Rotating Electrical Machines (IP Code)- Classification (IEC 60947-1: 2000,IDT)
GB/T 4942.2-1993 Degrees of Protection Provided by Enclosures for Low-voltage Apparatus (eqv. IEC 60947-1:1988)
GB/T 10068-2000 Mechanical Vibration of Certain Machines with Shaft Heights 56 mm and Higher-Measurement, Evaluation and Limits of Vibration (idt IEC idt IEC 60034-14: 1996)
GB 10069.3 Measurement of Airborne Noise Emitted by Rotating Electrical Machines and the Noise Limits-Part 3: Noise Limits (IEC 60034-9: 1997, IDT)
GB/T 12113-2003 Methods of Measurement of Touch Current and Protective Conductor Current (IEC 60990:1999, IDT)
GB/T 12665-1990 Requirements of Damp-heat Testing of Electrical Machine for Service in General Environmental Condition
GB/T 14023-2006 Vehicles Boats and Internal Combustion Engine Driven Devices-Radio Disturbance Characteristics-Limits and Methods of Measurement (CISPR 12: 2005, IDT)
GB 14711-2006 Safety Requirements of Small and Medium Size Rotating Electrical Machines
GB/T 17619-1998 Limits and methods of testing for immunity of electrical / electronic sub-assemblies in vehicles to electromagnetic radiation
GB/T 19596-2004 Terminology of Electric Vehicles (ISO 8713:2002, NEQ)
QC/T 413-2002 Basic Specification for Automotive Electrical Equipment
3 Duty and Limitation
Contents of GB/T 18488.1-2006
Foreword I
1 Scope
2 Normative References
3 Duty and Limitation
4 Environmental Conditions
5 Technical Requirements
6 Inspection Test Item
7 Type Test
8 Marking, Packaging, Transportation and Storage
Appendix A (Informative) Output Capacity Matching Relation of Single Electrical Machine and Controller
Appendix B (Informative) Urban Condition and Suburb Condition
