1 Scope
This standard specifies terms and definitions, technical requirements, marking and packaging of metal cutting bimetal band saw blades.
This standard is applicable to the metal cutting bimetal band saw blades (hereafter referred to as band saw blades) 6 mm ~ 80 mm in width, of which the saw tooth material is quick cutting steel or high-performance quick cutting steel and the saw blade material is low alloy spring steel.
2 Normative References
The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 230.1-2004 Metallic Rockwell Hardness Test - Part 1: Test Method (Scales A, B, C, D, E, F, G, H, K, N and T) (ISO 6508-1:1999, MOD)
GB/T 4340.1-1999 Metallic Materials - Vickers Hardness Test - Part 1: Test Method (eqv ISO 6507-1:1997)
GB/T 21954.1-2008 Metal Cutting Band Saw Blades - Part 1 - Terms (ISO 4875-1:2006, MOD)
GB/T 21954.2-2008 Metal Cutting Band Saw Blades - Part 1 - Characteristics and Dimensions (ISO 4875-2:2006, MOD)
JB/T 4318.3 Horizontal Band Sawing Machine - Part 3: Test of the Accuracy
JB/T 6050 Generalization of Hardness Test for Heat Treated Iron and Steel Parts
3 Terms and Definitions
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Technical Requirements
5 Marking and Packaging
Appendix A (Normative) Flexion Test for Band Saw Blades
1 Scope
This standard specifies terms and definitions, technical requirements, marking and packaging of metal cutting bimetal band saw blades.
This standard is applicable to the metal cutting bimetal band saw blades (hereafter referred to as band saw blades) 6 mm ~ 80 mm in width, of which the saw tooth material is quick cutting steel or high-performance quick cutting steel and the saw blade material is low alloy spring steel.
2 Normative References
The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 230.1-2004 Metallic Rockwell Hardness Test - Part 1: Test Method (Scales A, B, C, D, E, F, G, H, K, N and T) (ISO 6508-1:1999, MOD)
GB/T 4340.1-1999 Metallic Materials - Vickers Hardness Test - Part 1: Test Method (eqv ISO 6507-1:1997)
GB/T 21954.1-2008 Metal Cutting Band Saw Blades - Part 1 - Terms (ISO 4875-1:2006, MOD)
GB/T 21954.2-2008 Metal Cutting Band Saw Blades - Part 1 - Characteristics and Dimensions (ISO 4875-2:2006, MOD)
JB/T 4318.3 Horizontal Band Sawing Machine - Part 3: Test of the Accuracy
JB/T 6050 Generalization of Hardness Test for Heat Treated Iron and Steel Parts
3 Terms and Definitions
Contents of GB/T 25369-2010
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Technical Requirements
5 Marking and Packaging
Appendix A (Normative) Flexion Test for Band Saw Blades
