Foreword
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard replaces HG/T 2135-2014 Glass lined 180° elbows. In addition to editorial changes, the following main technical changes have been made with respect to HG/T 2135-2014:
——The applicable design pressure in Clause 1 "Scope" is revised from "not larger than 1.0 MPa" to "not larger than 1.6 MPa" (see Clause 1 hereof; Clause 1 of Edition 2014);
——The schematic diagram of loose flange and the radius r of the outer arc of nozzle are added in Figure 1 (see Figure 1 hereof);
——The technical contents of loose flange are added in Table 1 (see Table 1 hereof);
——The dimensions of the outer arc r of nozzle are added in Table 2 (see Table 2 hereof);
——The length symbol of elbow in Figure 1 and Table 2 is changed from “L” to “A”, the length symbol of elbow is changed from “H” to “K”, and the elbow height in Table 2 is revised from “130, 150, 160, 180, 200, 220, 240, 254, 304, 406, 508, 610, 812” to “130, 150, 160, 180, 200, 220, 240, 270, 305, 410, 510, 610, 815”, and the allowable deviation of elbow length in Table 3 is revised (see Tables 2 and 3 hereof; Tables 2 and 3 of Edition 2014);
——The requirements in Table 2 are revised from “value R in Figure 1 shall be selected according to GB/T 12459" to “Value R in Figure 1 shall be half of value A", and Note 2 is added (see Table 2 hereof; Table 2 of Edition 2014);
——The dimensions and reference mass of the nozzle with design pressure of 1.6MPa are added in Table 2 (see Table 2 hereof);
——"The materials, design, manufacture, inspection and acceptance of glass lined pressure pipes shall also meet the requirements of TSG D0001 and GB/T 20801.5” is added in 4.1 (see 4.1 hereof);
——The Table 4 is added (see Table 4 hereof);
——Technical requirements for non-destructive testing of non-pressure pipes are added in 4.5, i.e. “For non-pressure pipes, non-destructive testing shall be conducted according to NB/T 47003.1.” [See 4.5 b) hereof];
——Technical requirements for hydraulic test of non-pressure pipes are added in 4.6, i.e. “For non-pressure pipes, leakage test shall be conducted according to NB/T 47003.1.” [See 4.6b) hereof];
——“Value r of glass lined 180° elbows should be less than that specified in HG/T 2143.” is added in 4.7 (see 4.7 hereof);
——“the ex-factory data of glass lined pressure pipes shall also meet the requirements of TSG D0001” is added in 5.1 (see 5.1 hereof).
This standard was proposed by China Petroleum and Chemical Industry Federation.
This standard is under the jurisdiction of SAC/TC 72 National Technical Committee on Glass Lined Equipment of Standardization Administration of China.
The previous editions of this standard are as follows:
——HG/T 2135-1991; HG/T 2135-2009; HG/T 2135-2014.
Glass lined 180° elbows
1 Scope
The standard specified the type, basic parameters, main dimensions, requirements, ex-factory documents, packaging, transportation and storage of glass lined 180° elbows.
This standard is applicable to glass lined 180° elbows with a design pressure not greater than 1.6 MPa and a design temperature of -20℃~ 200℃.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1804 General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
GB/T 12459 Steel buttwelding pipe fittings - Types and parameter
GB/T 20801.5 Pressure piping code - Industrial piping - Part 5: Inspection and testing
GB 25,025 Specification of glass-lined equipment for industry
HG/T 2105 Loose flange for glass-lined equipment
HG/T 2143 Glass-lined steel vessel- Nozzles
NB/T 47003.1 Steel welded atmospheric pressure vessels
TSG D0001 Pressure pipe safety technology supervision regulation for industrial pressure pipe
3 Type, basic parameters, and main dimensions
3.1 The type, basic parameters and main dimensions of glass lined 180° elbows shall meet those specified in Figure 1 and Tables 1 and 2.
Foreword i
1 Scope
2 Normative references
3 Type, basic parameters, and main dimensions
4 Requirements
5 Ex-factory documents, packaging, transportation and storage
Foreword
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard replaces HG/T 2135-2014 Glass lined 180° elbows. In addition to editorial changes, the following main technical changes have been made with respect to HG/T 2135-2014:
——The applicable design pressure in Clause 1 "Scope" is revised from "not larger than 1.0 MPa" to "not larger than 1.6 MPa" (see Clause 1 hereof; Clause 1 of Edition 2014);
——The schematic diagram of loose flange and the radius r of the outer arc of nozzle are added in Figure 1 (see Figure 1 hereof);
——The technical contents of loose flange are added in Table 1 (see Table 1 hereof);
——The dimensions of the outer arc r of nozzle are added in Table 2 (see Table 2 hereof);
——The length symbol of elbow in Figure 1 and Table 2 is changed from “L” to “A”, the length symbol of elbow is changed from “H” to “K”, and the elbow height in Table 2 is revised from “130, 150, 160, 180, 200, 220, 240, 254, 304, 406, 508, 610, 812” to “130, 150, 160, 180, 200, 220, 240, 270, 305, 410, 510, 610, 815”, and the allowable deviation of elbow length in Table 3 is revised (see Tables 2 and 3 hereof; Tables 2 and 3 of Edition 2014);
——The requirements in Table 2 are revised from “value R in Figure 1 shall be selected according to GB/T 12459" to “Value R in Figure 1 shall be half of value A", and Note 2 is added (see Table 2 hereof; Table 2 of Edition 2014);
——The dimensions and reference mass of the nozzle with design pressure of 1.6MPa are added in Table 2 (see Table 2 hereof);
——"The materials, design, manufacture, inspection and acceptance of glass lined pressure pipes shall also meet the requirements of TSG D0001 and GB/T 20801.5” is added in 4.1 (see 4.1 hereof);
——The Table 4 is added (see Table 4 hereof);
——Technical requirements for non-destructive testing of non-pressure pipes are added in 4.5, i.e. “For non-pressure pipes, non-destructive testing shall be conducted according to NB/T 47003.1.” [See 4.5 b) hereof];
——Technical requirements for hydraulic test of non-pressure pipes are added in 4.6, i.e. “For non-pressure pipes, leakage test shall be conducted according to NB/T 47003.1.” [See 4.6b) hereof];
——“Value r of glass lined 180° elbows should be less than that specified in HG/T 2143.” is added in 4.7 (see 4.7 hereof);
——“the ex-factory data of glass lined pressure pipes shall also meet the requirements of TSG D0001” is added in 5.1 (see 5.1 hereof).
This standard was proposed by China Petroleum and Chemical Industry Federation.
This standard is under the jurisdiction of SAC/TC 72 National Technical Committee on Glass Lined Equipment of Standardization Administration of China.
The previous editions of this standard are as follows:
——HG/T 2135-1991; HG/T 2135-2009; HG/T 2135-2014.
Glass lined 180° elbows
1 Scope
The standard specified the type, basic parameters, main dimensions, requirements, ex-factory documents, packaging, transportation and storage of glass lined 180° elbows.
This standard is applicable to glass lined 180° elbows with a design pressure not greater than 1.6 MPa and a design temperature of -20℃~ 200℃.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1804 General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
GB/T 12459 Steel buttwelding pipe fittings - Types and parameter
GB/T 20801.5 Pressure piping code - Industrial piping - Part 5: Inspection and testing
GB 25,025 Specification of glass-lined equipment for industry
HG/T 2105 Loose flange for glass-lined equipment
HG/T 2143 Glass-lined steel vessel- Nozzles
NB/T 47003.1 Steel welded atmospheric pressure vessels
TSG D0001 Pressure pipe safety technology supervision regulation for industrial pressure pipe
3 Type, basic parameters, and main dimensions
3.1 The type, basic parameters and main dimensions of glass lined 180° elbows shall meet those specified in Figure 1 and Tables 1 and 2.
Contents of HG/T 2135-2021
Foreword i
1 Scope
2 Normative references
3 Type, basic parameters, and main dimensions
4 Requirements
5 Ex-factory documents, packaging, transportation and storage
