Detail of JB/T 10216-2013

Introduction of JB/T 10216-2013

1 Scope This standard specifies terms and definitions, model code, structure requirements, test methods, inspection rules, marking, transport and storage of cable support system for electric control distribution. This standard is applicable to cable supports system for indoor and outdoor high-and-low voltage power transmission and distribution engineering of industrial and civil buildings. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 12-2013 Cup Head Square Neck Bolts GB/T 93-1987 Single Coil Spring Lock Washers, Normal Type GB/T 97.1-2002 Plain Washers - Product Grade A GB/T 700-2006 Carbon Structural Steels GB 912-2008 Hot-rolled Sheets and Strips of Carbon Structural Steels and High Strength Low Alloy Structural Steels GB/T 1408.1-2006 Electrical Strength of Insulating Materials - Test Methods - Part 1: Tests at Power Frequencies GB/T 1410-2006 Methods of Test for Volume Resistivity and Surface Resistivity of Solid Electrical insulating Materials GB/T 1720-1979 Method of Test for Adhesion of Paint Films GB/T 1804-2000 General Tolerances - Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications GB/T 2423.4-2008 Environmental Testing for Electric and Electronic Products - Part 2: Test Method - Test Db: Damp Heat, Cyclic ( 12h+12h Cycle) GB/T 2423.17-2008 Environmental Testing for Electric and electronic Products - Part 2: Test Method - Test Ka: Salt Mist GB/T 2423.55-2006 Environmental Testing for Electric and Electronic Products - Part 2 : Test Methods - Test Eh: Hammer Tests GB/T 2573-2008 Test Method for Aging Properties of Glass Fiber Reinforced Plastics GB/T 3280-2007 Cold Rolled Stainless Steel Plate Sheet and Strip GB/T 3857-2005 Test Method for Chemical Resistance of Glass Fiber Reinforced Thermosetting Plastics GB/T 3880.1-2006 Wrought Aluminium and Aluminium Alloy Plates, Sheets and Strips for General Engineering - Part 1: Technical Conditions of Delivery GB 4208-2008 Degrees of Protection Provided by Enclosure (IP Code) GB/T 4956-2003 Non-magnetic Coatings on Magnetic Substrates - Measurement of Coating Thickness - Magnetic Method GB/T 5270-2005 Metallic Coatings on Metallic Substrates - Electrodeposited and Chemically Deposited Coatings - Revies of Methods Available for Testing Adhesion GB/T 5780-2000 Hexagon Head Bolts - Product Grade C GB/T 6170-2000 Hexagon Nuts, Style 1 GB/T 6892-2006 Wrought Aluminium and Aluminium Alloys Extruded Profiles for General Engineering GB 7251.1-2013 Low-voltage Switchgear and Controlgear Assemblies - Part 1: General Rules GB/T 8013.1-2007 Anodic Oxide Coating and Organic Polymer Coatings on Aluminium and Its Alloys - Part 1: Anodic Oxide Coatings GB/T 8237-2005 Liquid Unsaturated Polyester Resin for Fiber Reinforced Plastics GB 8624-2012 Classification for Burning Behavior of Building Materials and Products GB/T 9978.1-2008 Fire-resistance Tests - Elements of Building Construction - Part 1: General Requirements GB/T 10580-2003 Standard Conditions for Use Prior to and During the Testing of Solid Insulating Materials GB/T 11253-2007 Cold-rolled Sheets and Strips of Carbon Structural Steels GB/T 13452.2-2008 Paints and Varnishes - Determination of Film Thickness GB 14907-2002 Fire Resistive Coating for Steel Structure GB/T 18369-2008 Glass Fiber Roving GB/T 18370-2001 Glass Fibre Woven Roving GB/T 21762-2008 Cable Management - Cable Tray Systems and Cable Ladder Systems GB/T 23639-2009 Energy Conservation and Corrosion-resistant Steel-made Cable Support System JB/T 6743-1993 Corrosion-resistant Environmental Technical Requirements for Indoor and Outdoor Steel-made Cable Support System 3 Terms and Definitions 3.1 Terms and Definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 cable supports system full name of rigid structure system for supporting cable, which consists of straight segment, bend, system accessory as well as supports and pendants of cable tray or cable ladder (it is called support system for short) 3.1.2 cable tray assembly composed of base plate and side plate which forms a whole together with the base plate or is connected to the base plate

Contents of JB/T 10216-2013

Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 3.1 Terms and Definitions 3.2 Model Code 4 Structure Requirements 4.1 Normal Service Conditions 4.2 Special Service Conditions 4.3 Structure Requirements of Cable Support System 5 Test Methods 5.1 Inspection on Appearance and Dimensional Accuracy 5.2 Mechanical Load Test 5.3 Impact Test 5.4 Artificial Climate Protection Test 5.5 Performance Test for Various Surface Protective Layers 5.6 Protection Circuit Continuity Test 5.7 Protection Grade Test 5.8 Fire Resistance Grade Test for Fire-resistant Cable Support System 5.9 Performance Test for Glass Fiber Reinforced Plastic Support System, Composite Support System and Support Systems Made of Other Non-metal Fire Resistant Materials 6 Inspection Rules 6.1 Inspection Classification 6.2 Type Inspection 6.3 End-of-manufacturing Inspection 6.4 Sampling and Judgment 7 Marking, Transport and Storage 7.1 Marking and Nameplate 7.2 Transport and Storage Annex A (Informative) Typical Legend of Tray and Ladder Annex B (Informative) Schematic Diagram for Typical Supports and Pendants Annex C (Informative) Use Recommendation under Different Environments for Cable Supports System Figure 1 Layout Form for the Load Test of Straight Sections Figure 2 Layout Form for the Load Test of Joint of Straight Section Figure 3 Typical Test Layouts for Bends Figure 4 Typical Positioning Modes for Fixing Body of Test Supports and Tested Supports and Pendants Figure 5 Test Sample Layout Drawing for Impact Test Figure 6 Layout Drawing for Electrical Continuity Test Figure 7 Installation Diagram for Support System in the Furnace Figure 8 Schematic Diagram for Cable Laying in Fire-resistant Cable Support System Figure 9 Wiring for Fire Resistance Test of Power Cable Figure 10 Wiring for Fire Resistance Test of Control Cable Figure A.1 Solid Bottom Cable Tray Length Figure A.2 Perforated Cable Tray Length Figure A.3 Cable Tray of Assembly Length Figure A.4 Mesh Cable Tray Length Figure A.5 Cable Ladder Length Figure A.6 Double-side Cable Supports System Length Figure B.1 Typical Supports and Pendants Table 1 Support System Main Structure Material and Code Table 2 Structural Feature Code Table 3 Codes of Main Varieties Table 4 Cable Support System Protection Type and Corresponding Service Environment Condition Grade Table 5 Fire Resistance Class and Code of Fire-resistant Cable Support System Table 6 Parameters of Different Climatic Environment Grades Table 7 Parameters of Different Chemical Corrosion Environments Table 8 Recommended Common Specifications and Dimensions Table 9 Permissible Minimum Plate Thickness of Support System Table 10 Technical Requirements of Surface Protective Layer Table 11 Safe Working Load (SWL) of Typical Cable Support System Table 12 Artificial Climate Test Items and Test Periods Table 13 Performance Test Items for Various Surface Protective Layers Table 14 Performance Test for Glass Fiber Reinforced Plastic Support System, Composite Support System and Support Systems Made of Other Non-metal Fire Resistant Materials Table C.1 Use Recommendation under Different Environments for Cable Supports System