Certification and Accreditation Administration of the People's Republic of China
Issued on:
July 16, 2014
Implemented on:
2014-9-1
Status:
valid
Target Language:
English
File Format:
PDF
Word Count:
4000 words
Translation Price(USD):
70.0
Delivery:
via email in 1 business day
0 Introduction
This Rule is prepared basing on safety risks and certification risks of low voltage switchgear and specifies the basic principles and requirements for implementing compulsory product certification of low voltage switchgear.
This Rule is used jointly with general applicable rules issued by CNCA, like "Implementation Rules for Compulsory Product Certification - Classification Management of Manufacturers, Certification Mode Selection and Determination", "Implementation Rules for Compulsory Product Certification - Application of Manufacturer Inspection Resources and Other Certification Results", "Implementation Rules for Compulsory Product Certification - General Requirements for Factory Inspection".
The certification body shall, in accordance with the requirements of general applicable rules and this Rule, formulate certification implementation rules which shall also be implemented jointly with general applicable rules and this Rule.
Manufacturers shall ensure that their certified products always meet the requirements of certification and applicable standards.
1 Application Scope
This Rule is applicable to low voltage switchgear, including power switchgear set having 1000V AC rated voltage and 1000Hz or less frequency, busbar trunking system (busway), distribution board, assemblies for construction sites (ACS), assemblies for power distribution in public networks and reactive power compensator.
The application scope adjustment caused by changes, e.g. laws & regulations or relevant product standards, techniques, and industrial policies, shall be subject to CNCA announcement.
2 Terms and Definitions
In this Rule, design appraisal, a non-experimental verification measure, refers to methods of validation comparison and validation evaluation to prove that products comply to the certification standards.
3 Certification References
... ...
... ...
The above standards shall be the latest edition issued by the administrative department for standardization under the State Council in principle. Where other editions are needed, the standards in question shall be implemented in accordance with the announcement required by applicable relevant standards issued by CNCA.
4 Certification Mode
Basic certification mode for compulsory certification of low voltage switchgear is as follows:
Type test + follow-up inspection after certification
Or
Design appraisal + type test for some items + follow-up inspection after certification
Where the enterprise has the design capacity and reference data for design appraisal, the design appraisal may be adopted to replace the partial type test inspection items after being determined by certification body; otherwise, the products shall be subjected to the full-item type test for conformance to the certification standards.
0 Introduction
1 Application Scope
2 Terms and Definitions
3 Certification References
4 Certification Mode
5 Certification Unit Division
6 Certification Entrustment
6.1 Proposal and Acceptance of Certification Entrustment
6.2 Application Information
6.3 Implementation Arrangement
7 Certification Implementation
7.1 Type Test
7.2 Appraisal of Design
7.3 Certification Assessment and Determination
7.4 Certification Time Limit
8 Supervision after Certification
8.1 Follow-up Inspection after Certification
8.2 Frequency and Time of Supervision after Certification
8.3 Record
8.4 Result Assessment
9 Certificate
9.1 Maintenance of Certificate
9.2 Modification of Products covered by Certificate
9.3 Expansion of Certificate-covered Product
9.4 Cancellation, Suspension and Revocation of Certificate
9.5 Application of Certificate
10 Certification Mark
10.1 Permissible Marks
10.2 Marking Mode
11 Charge
12 Certification Responsibility
13 Certification Implementation Rules
Standard
CNCA-C03-01:2014 Implementation Rule for Compulsory Product Certification Low Voltage Switchgear for Low Voltage Apparatus (English Version)
Standard No.
CNCA-C03-01:2014
Status
valid
Language
English
File Format
PDF
Word Count
4000 words
Price(USD)
70.0
Implemented on
2014-9-1
Delivery
via email in 1 business day
Detail of CNCA-C03-01:2014
Standard No.
CNCA-C03-01:2014
English Name
Implementation Rule for Compulsory Product Certification Low Voltage Switchgear for Low Voltage Apparatus
Chinese Name
强制性产品认证实施规则 低压电器 低压成套开关设备
Chinese Classification
Professional Classification
CN
ICS Classification
Issued by
Certification and Accreditation Administration of the People's Republic of China
Issued on
July 16, 2014
Implemented on
2014-9-1
Status
valid
Superseded by
Superseded on
Abolished on
Superseding
Language
English
File Format
PDF
Word Count
4000 words
Price(USD)
70.0
Keywords
CNCA-C03-01:2014, , CNCA-C03-01:2014, CNCA,
Introduction of CNCA-C03-01:2014
0 Introduction
This Rule is prepared basing on safety risks and certification risks of low voltage switchgear and specifies the basic principles and requirements for implementing compulsory product certification of low voltage switchgear.
This Rule is used jointly with general applicable rules issued by CNCA, like "Implementation Rules for Compulsory Product Certification - Classification Management of Manufacturers, Certification Mode Selection and Determination", "Implementation Rules for Compulsory Product Certification - Application of Manufacturer Inspection Resources and Other Certification Results", "Implementation Rules for Compulsory Product Certification - General Requirements for Factory Inspection".
The certification body shall, in accordance with the requirements of general applicable rules and this Rule, formulate certification implementation rules which shall also be implemented jointly with general applicable rules and this Rule.
Manufacturers shall ensure that their certified products always meet the requirements of certification and applicable standards.
1 Application Scope
This Rule is applicable to low voltage switchgear, including power switchgear set having 1000V AC rated voltage and 1000Hz or less frequency, busbar trunking system (busway), distribution board, assemblies for construction sites (ACS), assemblies for power distribution in public networks and reactive power compensator.
The application scope adjustment caused by changes, e.g. laws & regulations or relevant product standards, techniques, and industrial policies, shall be subject to CNCA announcement.
2 Terms and Definitions
In this Rule, design appraisal, a non-experimental verification measure, refers to methods of validation comparison and validation evaluation to prove that products comply to the certification standards.
3 Certification References
... ...
... ...
The above standards shall be the latest edition issued by the administrative department for standardization under the State Council in principle. Where other editions are needed, the standards in question shall be implemented in accordance with the announcement required by applicable relevant standards issued by CNCA.
4 Certification Mode
Basic certification mode for compulsory certification of low voltage switchgear is as follows:
Type test + follow-up inspection after certification
Or
Design appraisal + type test for some items + follow-up inspection after certification
Where the enterprise has the design capacity and reference data for design appraisal, the design appraisal may be adopted to replace the partial type test inspection items after being determined by certification body; otherwise, the products shall be subjected to the full-item type test for conformance to the certification standards.
Contents of CNCA-C03-01:2014
0 Introduction
1 Application Scope
2 Terms and Definitions
3 Certification References
4 Certification Mode
5 Certification Unit Division
6 Certification Entrustment
6.1 Proposal and Acceptance of Certification Entrustment
6.2 Application Information
6.3 Implementation Arrangement
7 Certification Implementation
7.1 Type Test
7.2 Appraisal of Design
7.3 Certification Assessment and Determination
7.4 Certification Time Limit
8 Supervision after Certification
8.1 Follow-up Inspection after Certification
8.2 Frequency and Time of Supervision after Certification
8.3 Record
8.4 Result Assessment
9 Certificate
9.1 Maintenance of Certificate
9.2 Modification of Products covered by Certificate
9.3 Expansion of Certificate-covered Product
9.4 Cancellation, Suspension and Revocation of Certificate
9.5 Application of Certificate
10 Certification Mark
10.1 Permissible Marks
10.2 Marking Mode
11 Charge
12 Certification Responsibility
13 Certification Implementation Rules
