1 Scope
This standard specifies the technical requirements, tests, inspection rules, marking and packaging of the insulation piercing connector for rated voltages up to 10kV.
This standard is applicable to the insulation piercing connectors used for aerial insulated wire, bridge and culvert, adit, tunnel, mineral drive and wire pipe shaft with rated voltage for rated voltage up to 10KV.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to (excluding amending errors in the text), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of the normative document is applicable. For undated references, the latest edition of the normative document applies.
GB/T 2314 General Technical Requirements for Electric Power Fittings
GB/T 2317.3 Test Method for Electric Power Fittings - Part 3: Heat Cycle Tests for Electric Power Fittings
GB/T 3048.7 Test Methods for Electrical Properties of Electric Cables and Wires - Part 7: Tracking Resistance Test
GB/T 12527 Aerial Insulated Cables of Rated Voltage Up to and including 1kV
GB/T 14049 Aerial Insulated Cables for Rated Voltage of 10kV
GB/T 16927.1 High Voltage Test Techniques - Part 1: General Test Requirements
GB/T 16927.2 High Voltage Test Techniques - Part 2: Measuring Systems
DL/T 765.1 Technical Requirements for Distribution Fittings
DL/T 765.3 Overhead Insulated Conductor Fittings of Rated Voltages Up to 10kv
DL/T 768.7 Manufacture Quality Specification for Electric Power Fittings Hot Dip Galvanized Coatings on Fabricated Iron and Steel Articles
3 Terms and Definitions
Foreword I
1 Scope
2 Normative References
3 Terms and Definitions
4 Technical Requirements
5 Tests
6 Inspection Rules
7 Marking and Packaging
Appendix A (Informative) Installation Requirements
Appendix B (Normative) Resistance Test Arrangement and Calculation
Appendix C (Normative) Typical Test Loop of Electrical Test
Appendix D (Informative) Bibliography
1 Scope
This standard specifies the technical requirements, tests, inspection rules, marking and packaging of the insulation piercing connector for rated voltages up to 10kV.
This standard is applicable to the insulation piercing connectors used for aerial insulated wire, bridge and culvert, adit, tunnel, mineral drive and wire pipe shaft with rated voltage for rated voltage up to 10KV.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to (excluding amending errors in the text), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of the normative document is applicable. For undated references, the latest edition of the normative document applies.
GB/T 2314 General Technical Requirements for Electric Power Fittings
GB/T 2317.3 Test Method for Electric Power Fittings - Part 3: Heat Cycle Tests for Electric Power Fittings
GB/T 3048.7 Test Methods for Electrical Properties of Electric Cables and Wires - Part 7: Tracking Resistance Test
GB/T 12527 Aerial Insulated Cables of Rated Voltage Up to and including 1kV
GB/T 14049 Aerial Insulated Cables for Rated Voltage of 10kV
GB/T 16927.1 High Voltage Test Techniques - Part 1: General Test Requirements
GB/T 16927.2 High Voltage Test Techniques - Part 2: Measuring Systems
DL/T 765.1 Technical Requirements for Distribution Fittings
DL/T 765.3 Overhead Insulated Conductor Fittings of Rated Voltages Up to 10kv
DL/T 768.7 Manufacture Quality Specification for Electric Power Fittings Hot Dip Galvanized Coatings on Fabricated Iron and Steel Articles
3 Terms and Definitions
Contents of DL/T 1190-2012
Foreword I
1 Scope
2 Normative References
3 Terms and Definitions
4 Technical Requirements
5 Tests
6 Inspection Rules
7 Marking and Packaging
Appendix A (Informative) Installation Requirements
Appendix B (Normative) Resistance Test Arrangement and Calculation
Appendix C (Normative) Typical Test Loop of Electrical Test
Appendix D (Informative) Bibliography
