Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard was proposed by China National Textile and Apparel Council.
This standard is under the jurisdiction of Technical Subcommittee for Sportswear of National Technical Committee for Standardization of Sports Goods (SAC/TC 291/SC 1) and National Technical Committee on Garments of Standardization Administration of China (SAC/TC 219).
UV-protective light weight outdoor clothing
1 Scope
This standard specifies the terms and definitions, requirements, inspection methods, inspection rules as well as marking, packaging, transportation and storage of UV-protective light weight outdoor clothing.
This standard is applicable to the UV-protective light weight outdoor clothing mainly made of lightweight textile fabrics.
This standard is not applicable to the light weight outdoor clothing for infants and young children aged 36 months and below.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 250 Textiles - Tests for color fastness - Grey scale for assessing change in color
GB/T 1335 (All parts) Standard sizing systems for garments
GB/T 3917.2 Textiles - Tear properties of fabrics - Part 2: Determination of tear force of trouser-shaped test specimens (single tear method)
GB/T 3921-2008 Textiles - Tests for colour fastness - Colour fastness to washing with soap or soap and soda
GB/T 4841.3 Colour cards of standard depths for dyeing with dyestuffs 2/1, 1/3, 1/6, 1/12, 1/25
GB/T 5296.4 Instructions for use of products of consumer interest - Part 4: Textiles and apparel
GB/T 8427-2008 Textiles - Tests for color fastness - Color fastness to artificial light: Xenon arc fading lamp test
GB/T 8629-2017 Textiles - Domestic washing and drying procedures for textile testing
GB/T 8630 Textiles - Determination of dimensional change in washing and drying
GB/T 12704.1-2009 Textiles - Test method for water-vapour transmission of fabrics - Part 1: Desiccant method
GB/T 14801 Test method for skewness and bow in woven and knitted fabrics
GB/T 15557 Standard terminology relating to apparel
GB 18401 National general safety technical code for textile products
GB/T 18830 Textiles - Evaluation for solar ultraviolet radiation protective properties
GB/T 21294 Testing methods of physical and chemical performance of garments
GB/T 21295-2014 Requirements of physical and chemical performance of garments
GB/T 29862 Textiles - Identification of fiber content
GB 31701 Safety technical code for infants and children textile products
GB/T 31702 Testing method for sharpness of attached components on textile products
GB/T 31907 Method of garment measurement
FZ/T 80002 Marking, packaging, transportation and storage for garments
FZ/T 80004 Rule for garments delivery inspection
3 Terms and definitions
For the purposes of this document, the terms and definitions established in GB/T 15557 and the following apply.
3.1
UV-protective light weight outdoor clothing
outdoor clothing which is mainly made of textile fabrics with UV-protective function and with the conventional mass per square meter of single-layer fabrics (or the sum of conventional mass per square meter of multi-layer fabrics) not greater than 60g/m2
3.2
fluorescent color
color named according to the characteristic of dye or pigment that it shows color by absorbing light and emitting light and fluorescence within the area with visible light
4 Requirements
4.1 Instructions for use
The instructions for use shall be in accordance with GB/T 5296.4 and GB 31701.
4.2 Size specification
4.2.1 Size specification shall be set according to the requirements of GB/T 1335.
4.2.2 The specification of main parts shall be designed according to the relevant requirements of GB/T 1335.
4.3 Raw materials
4.3.1 Shell fabric
Shell fabric complying with the quality requirements of this standard shall be adopted.
4.3.2 Auxiliary materials
4.3.2.1 Lining cloth, border lace and pocket bag
Lining cloth, border lace and pocket bag suitable to the performance of the used shell fabric shall be adopted and their quality shall meet the relevant requirements of this standard.
4.3.2.2 Sewing thread, rope belt and elastic ribbon
Sewing thread, rope belt and elastic ribbon (except ornamental thread and belt) suitable to the performance of the used shell fabric and auxiliary materials shall be adopted.
4.3.2.3 Button, zipper and other accessories
Buttons (except ornamental buttons), zippers and other accessories suitable for the adopted shell fabric shall be used. Button, ornamental button, zipper and other accessories shall be smooth in surface and free of burr, damage, defect and accessible sharp tip or edge. Zippers shall mesh in good condition and run smoothly.
Note: accessible sharp tip and edge are the sharp edge and tip on finished product that may cause harm to human skin under normal wearing.
4.4 Warp and weft yarn
The yarn skewness of top collar, bodice and sleeves shall not be greater than 3%. The front bottom hem shall be free from any upwarp.
4.5 Strip and plaid matching
4.5.1 Obvious strips or plaids of 1.0cm or above on shell fabric shall comply with those specified in Table 1.
Table 1 In cm
Part Requirements for strip and plaid
Left and right front Strips are matched with each other and plaids are matched each other horizontally, with the mutual deviation not greater than 0.3
Sleeve seam For the part below sleeve elbow line, the plaids of rear sleeve seam are matched with each other horizontally, with the mutual deviation not greater than 0.3
Back seam Strips are matched with each other and plaids are matched each other horizontally, with the mutual deviation not greater than 0.2
Sleeves Strips and plaids shall be straight in relation to the sleeve top, with the mutual deviation not greater than 0.5
Notes:
1 The strips and plaids with color cycling shall be matched with each other based on the cycle.
2 Special design is free from such limitation.
4.5.2 Shell fabrics have obvious strips or plaids of 0.5~1.0cm (excluding 1.0cm); for the pocket and front, strips and plaids are matched with each other, with the mutual deviation not greater than 0.2cm (except in special design).
4.5.3 Shell fabric with special pattern shall be subject to the main pattern and the grain direction all over the body shall be consistent.
4.6 Color difference
For finished products, the color difference of top collar from the front is greater than Grade 4, and that of other surface part is not lower than Grade 4 (except in special design).
4.7 Appearance defects
The defect permissibility for each part of finished product shall comply with those specified in Table 2. See Figure 1 for each part of finished product. Only one defect within permissibility is permissible at each part. The defects not covered in this standard shall be in accordance with the requirements for similar ones in the table below based on their forms.
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Inspection methods
6 Inspection rules
7 Marking, packaging, transportation and storage
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard was proposed by China National Textile and Apparel Council.
This standard is under the jurisdiction of Technical Subcommittee for Sportswear of National Technical Committee for Standardization of Sports Goods (SAC/TC 291/SC 1) and National Technical Committee on Garments of Standardization Administration of China (SAC/TC 219).
UV-protective light weight outdoor clothing
1 Scope
This standard specifies the terms and definitions, requirements, inspection methods, inspection rules as well as marking, packaging, transportation and storage of UV-protective light weight outdoor clothing.
This standard is applicable to the UV-protective light weight outdoor clothing mainly made of lightweight textile fabrics.
This standard is not applicable to the light weight outdoor clothing for infants and young children aged 36 months and below.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 250 Textiles - Tests for color fastness - Grey scale for assessing change in color
GB/T 1335 (All parts) Standard sizing systems for garments
GB/T 3917.2 Textiles - Tear properties of fabrics - Part 2: Determination of tear force of trouser-shaped test specimens (single tear method)
GB/T 3921-2008 Textiles - Tests for colour fastness - Colour fastness to washing with soap or soap and soda
GB/T 4841.3 Colour cards of standard depths for dyeing with dyestuffs 2/1, 1/3, 1/6, 1/12, 1/25
GB/T 5296.4 Instructions for use of products of consumer interest - Part 4: Textiles and apparel
GB/T 8427-2008 Textiles - Tests for color fastness - Color fastness to artificial light: Xenon arc fading lamp test
GB/T 8629-2017 Textiles - Domestic washing and drying procedures for textile testing
GB/T 8630 Textiles - Determination of dimensional change in washing and drying
GB/T 12704.1-2009 Textiles - Test method for water-vapour transmission of fabrics - Part 1: Desiccant method
GB/T 14801 Test method for skewness and bow in woven and knitted fabrics
GB/T 15557 Standard terminology relating to apparel
GB 18401 National general safety technical code for textile products
GB/T 18830 Textiles - Evaluation for solar ultraviolet radiation protective properties
GB/T 21294 Testing methods of physical and chemical performance of garments
GB/T 21295-2014 Requirements of physical and chemical performance of garments
GB/T 29862 Textiles - Identification of fiber content
GB 31701 Safety technical code for infants and children textile products
GB/T 31702 Testing method for sharpness of attached components on textile products
GB/T 31907 Method of garment measurement
FZ/T 80002 Marking, packaging, transportation and storage for garments
FZ/T 80004 Rule for garments delivery inspection
3 Terms and definitions
For the purposes of this document, the terms and definitions established in GB/T 15557 and the following apply.
3.1
UV-protective light weight outdoor clothing
outdoor clothing which is mainly made of textile fabrics with UV-protective function and with the conventional mass per square meter of single-layer fabrics (or the sum of conventional mass per square meter of multi-layer fabrics) not greater than 60g/m2
3.2
fluorescent color
color named according to the characteristic of dye or pigment that it shows color by absorbing light and emitting light and fluorescence within the area with visible light
4 Requirements
4.1 Instructions for use
The instructions for use shall be in accordance with GB/T 5296.4 and GB 31701.
4.2 Size specification
4.2.1 Size specification shall be set according to the requirements of GB/T 1335.
4.2.2 The specification of main parts shall be designed according to the relevant requirements of GB/T 1335.
4.3 Raw materials
4.3.1 Shell fabric
Shell fabric complying with the quality requirements of this standard shall be adopted.
4.3.2 Auxiliary materials
4.3.2.1 Lining cloth, border lace and pocket bag
Lining cloth, border lace and pocket bag suitable to the performance of the used shell fabric shall be adopted and their quality shall meet the relevant requirements of this standard.
4.3.2.2 Sewing thread, rope belt and elastic ribbon
Sewing thread, rope belt and elastic ribbon (except ornamental thread and belt) suitable to the performance of the used shell fabric and auxiliary materials shall be adopted.
4.3.2.3 Button, zipper and other accessories
Buttons (except ornamental buttons), zippers and other accessories suitable for the adopted shell fabric shall be used. Button, ornamental button, zipper and other accessories shall be smooth in surface and free of burr, damage, defect and accessible sharp tip or edge. Zippers shall mesh in good condition and run smoothly.
Note: accessible sharp tip and edge are the sharp edge and tip on finished product that may cause harm to human skin under normal wearing.
4.4 Warp and weft yarn
The yarn skewness of top collar, bodice and sleeves shall not be greater than 3%. The front bottom hem shall be free from any upwarp.
4.5 Strip and plaid matching
4.5.1 Obvious strips or plaids of 1.0cm or above on shell fabric shall comply with those specified in Table 1.
Table 1 In cm
Part Requirements for strip and plaid
Left and right front Strips are matched with each other and plaids are matched each other horizontally, with the mutual deviation not greater than 0.3
Sleeve seam For the part below sleeve elbow line, the plaids of rear sleeve seam are matched with each other horizontally, with the mutual deviation not greater than 0.3
Back seam Strips are matched with each other and plaids are matched each other horizontally, with the mutual deviation not greater than 0.2
Sleeves Strips and plaids shall be straight in relation to the sleeve top, with the mutual deviation not greater than 0.5
Notes:
1 The strips and plaids with color cycling shall be matched with each other based on the cycle.
2 Special design is free from such limitation.
4.5.2 Shell fabrics have obvious strips or plaids of 0.5~1.0cm (excluding 1.0cm); for the pocket and front, strips and plaids are matched with each other, with the mutual deviation not greater than 0.2cm (except in special design).
4.5.3 Shell fabric with special pattern shall be subject to the main pattern and the grain direction all over the body shall be consistent.
4.6 Color difference
For finished products, the color difference of top collar from the front is greater than Grade 4, and that of other surface part is not lower than Grade 4 (except in special design).
4.7 Appearance defects
The defect permissibility for each part of finished product shall comply with those specified in Table 2. See Figure 1 for each part of finished product. Only one defect within permissibility is permissible at each part. The defects not covered in this standard shall be in accordance with the requirements for similar ones in the table below based on their forms.
Contents of FZ/T 74007-2019
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Inspection methods
6 Inspection rules
7 Marking, packaging, transportation and storage
