General specifications of burglary resistant fingerprint locks
1 Scope
This standard specifies the general technical requirements and test methods for burglary resistant fingerprint locks, and is the technical basis for designing, manufacturing and inspecting burglary resistant fingerprint locks.
This standard is applicable to locks with certain anti-vandalism ability that use fingerprints as input signals, identify and process relevant information, and electrically control the unlocking and locking of mechanical locking structures.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 2828.1-2003 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (ISO 2859-1: 1999, IDT)
GB/T 6461-2002 Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates - Rating of test specimens and manufactured articles subjected to corrosion tests (ISO 10289: 1999, IDT)
GB/T 10125-1997 Corrosion tests in artificial atmospheres - Salt spray tests (eqv ISO 9227: 1990)
GB/T 15211-1994 Environmental testing for alarm systems
GB/T 17626.2-2006 Electromagnetic compatibility (EMC) - Testing and measurement techniques - Electrostatic discharge immunity test (IEC 61000-4-2: 2001, IDT)
GB/T 17626.3-2006 Electromagnetic compatibility - Testing and measurement techniques - Radiated radio-frequency electromagnetic field immunity test (IEC 61000-4-3: 2002, IDT)
GB/T 17626.4-1998 Electromagnetic compatibility - Testing and measurement techniques - Electrical fast transient/burst immunity test (idt IEC 61000-4-4: 1995)
GB/T 17626.11-1999 Electromagnetic compatibility - Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests (idt IEC 61000-4-11: 1994)
GA/T 73-1994 Burglary-resistant mechanical locks
GA 374-2001 Burglary-resistant electronic locks
GA/T 394-2002 Specifications of access control system
3 Terms and definitions
For the purposes of this standard, the following term and definition apply:
3.1
burglary resistant fingerprint locks
locks with certain anti-vandalism ability that directly use fingerprints as input signals, and identify and process relevant information to control the mechanical actuator to implement the unlocking and locking
3.2
standalone module for fingerprint recognition
collection of intelligent circuits consisting of a microprocessor and related peripheral circuit devices with fingerprint enrollment, deletion, matching and management functions
3.3
fingerprint template
a set of data extracted from a fingerprint image after processing that characterizes the inherent features of the fingerprint image
3.4
fingerprint enrollment
process of collecting fingerprint images, processing them, extracting fingerprint template as the basis for fingerprint matching and storing them in a certain format
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Composition
5 Product safety classification
6 Technical requirements
7 Test methods
8 Inspection rules
9 Marking, packaging, transportation and storage
Annex A (Informative) Test methods for “false accept rate” and “false rejection rate”
Annex B (Informative) Definition of API interface function for communication
GA 701-2007, GA/T 701-2007, GAT 701-2007, GA701-2007, GA 701, GA701, GA/T701-2007, GA/T 701, GA/T701, GAT701-2007, GAT 701, GAT701
Introduction of GA 701-2007
General specifications of burglary resistant fingerprint locks
1 Scope
This standard specifies the general technical requirements and test methods for burglary resistant fingerprint locks, and is the technical basis for designing, manufacturing and inspecting burglary resistant fingerprint locks.
This standard is applicable to locks with certain anti-vandalism ability that use fingerprints as input signals, identify and process relevant information, and electrically control the unlocking and locking of mechanical locking structures.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 2828.1-2003 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (ISO 2859-1: 1999, IDT)
GB/T 6461-2002 Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates - Rating of test specimens and manufactured articles subjected to corrosion tests (ISO 10289: 1999, IDT)
GB/T 10125-1997 Corrosion tests in artificial atmospheres - Salt spray tests (eqv ISO 9227: 1990)
GB/T 15211-1994 Environmental testing for alarm systems
GB/T 17626.2-2006 Electromagnetic compatibility (EMC) - Testing and measurement techniques - Electrostatic discharge immunity test (IEC 61000-4-2: 2001, IDT)
GB/T 17626.3-2006 Electromagnetic compatibility - Testing and measurement techniques - Radiated radio-frequency electromagnetic field immunity test (IEC 61000-4-3: 2002, IDT)
GB/T 17626.4-1998 Electromagnetic compatibility - Testing and measurement techniques - Electrical fast transient/burst immunity test (idt IEC 61000-4-4: 1995)
GB/T 17626.11-1999 Electromagnetic compatibility - Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests (idt IEC 61000-4-11: 1994)
GA/T 73-1994 Burglary-resistant mechanical locks
GA 374-2001 Burglary-resistant electronic locks
GA/T 394-2002 Specifications of access control system
3 Terms and definitions
For the purposes of this standard, the following term and definition apply:
3.1
burglary resistant fingerprint locks
locks with certain anti-vandalism ability that directly use fingerprints as input signals, and identify and process relevant information to control the mechanical actuator to implement the unlocking and locking
3.2
standalone module for fingerprint recognition
collection of intelligent circuits consisting of a microprocessor and related peripheral circuit devices with fingerprint enrollment, deletion, matching and management functions
3.3
fingerprint template
a set of data extracted from a fingerprint image after processing that characterizes the inherent features of the fingerprint image
3.4
fingerprint enrollment
process of collecting fingerprint images, processing them, extracting fingerprint template as the basis for fingerprint matching and storing them in a certain format
Contents of GA 701-2007
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Composition
5 Product safety classification
6 Technical requirements
7 Test methods
8 Inspection rules
9 Marking, packaging, transportation and storage
Annex A (Informative) Test methods for “false accept rate” and “false rejection rate”
Annex B (Informative) Definition of API interface function for communication
