1 Scope
This part of GB 18241 specifies the classification and mark, requirements, test method, inspection rules as well as marking, packaging, transport and storage of lining for flue gas desulfurization (hereafter referred to as “lining”).
This part is mainly applicable to the lining laminated to the wet process flue gas desulfurization device to prevent the device from being corroded by wet and hot sulfur dioxide flue gas, condensed sulfuric acid, lime water suspension, calcium chloride solution and other media.
This part is also applicable to other flue gas desulfurization devices under similar wet desulfurization conditions.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of GB 18241. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this part of GB 18241. However parties to agreements based on this part of GB 18241 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 528 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties (GB/T 528-1998; eqv ISO 37: 1994)
GB/T 531 Rubber - Determination of indentation hardness by means of pocket hardness meters (GB/T 531-1999; idt ISO 7619: 1986)
GB/T 1690 Rubber, vulcanized－Determination of the effect of liquids (GB/T 1690-1992; neq ISO 1817: 1985)
GB/T 7760 Rubber, vulcanized or thermoplastic - Determination of adhesion to a rigid substrate - 90 degrees peel method (GB/T 7760-2003; ISO 813: 1997, MOD)
GB/T 8923-1988 Rust grades and preparation grades of steel surfaces before application of paints and related products (eqv ISO 8501-1: 1988)
3 Product classification and mark
3.1 See Table 1 for the classification of linings by rubber type.
Foreword i
1 Scope
2 Normative references
3 Product classification and mark
4 Requirements
5 Test methods
6 Inspection rules
7 Marking, packaging, transport and storage
Annex A (Normative) Determination of adhesion strength of linings (90 degrees peel method)
Annex B (Normative) Test for integrity of linings
Annex C (Normative) Test for applicability of linings
1 Scope
This part of GB 18241 specifies the classification and mark, requirements, test method, inspection rules as well as marking, packaging, transport and storage of lining for flue gas desulfurization (hereafter referred to as “lining”).
This part is mainly applicable to the lining laminated to the wet process flue gas desulfurization device to prevent the device from being corroded by wet and hot sulfur dioxide flue gas, condensed sulfuric acid, lime water suspension, calcium chloride solution and other media.
This part is also applicable to other flue gas desulfurization devices under similar wet desulfurization conditions.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of GB 18241. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this part of GB 18241. However parties to agreements based on this part of GB 18241 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 528 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties (GB/T 528-1998; eqv ISO 37: 1994)
GB/T 531 Rubber - Determination of indentation hardness by means of pocket hardness meters (GB/T 531-1999; idt ISO 7619: 1986)
GB/T 1690 Rubber, vulcanized－Determination of the effect of liquids (GB/T 1690-1992; neq ISO 1817: 1985)
GB/T 7760 Rubber, vulcanized or thermoplastic - Determination of adhesion to a rigid substrate - 90 degrees peel method (GB/T 7760-2003; ISO 813: 1997, MOD)
GB/T 8923-1988 Rust grades and preparation grades of steel surfaces before application of paints and related products (eqv ISO 8501-1: 1988)
3 Product classification and mark
3.1 See Table 1 for the classification of linings by rubber type.
Contents of GB 18241.4-2006
Foreword i
1 Scope
2 Normative references
3 Product classification and mark
4 Requirements
5 Test methods
6 Inspection rules
7 Marking, packaging, transport and storage
Annex A (Normative) Determination of adhesion strength of linings (90 degrees peel method)
Annex B (Normative) Test for integrity of linings
Annex C (Normative) Test for applicability of linings
