GB 25751-2010 Compression gas spring technical specification
1 Scope
This standard specifies the terms and definitions, designation, technical requirements, test methods and inspection rules for compression gas springs (hereinafter referred to as “gas springs”), as well as requirements for their marking, packaging, transport and storage, among other matters.
This standard is applicable to gas springs that use nitrogen or other inert gases as the working medium for energy storage.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 1771 Paints and varnishes—Determination of resistance to neutral salt spray (fog) (GB/T 1771—2007, ISO 7253:1996, IDT)
GB/T 1800.1 Geometrical product specifications (GPS)—Limits and fits—Part 1: Bases of tolerances, deviations and fits (GB/T 1800.1—2009, ISO 286-1:1988, MOD)
GB/T 1805 Nomenclature of springs
GB/T 2348 Fluid power systems and components—Cylinder bores and piston rod diameters (GB/T 2348—1993, neq ISO 3320:1987)
GB/T 2349 Fluid power systems and components—Cylinders—Basic series of piston strokes
GB/T 2828.1 Sampling procedures for inspection by attributes—Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1—2003, ISO 2859-1:1999, IDT)
GB/T 2829 Sampling procedures and tables for periodic inspection by attributes (apply to inspection of process stability)
GB/T 10125 Corrosion tests in artificial atmospheres—Salt spray tests (GB/T 10125—1997, eqv ISO 9227:1990)
QC/T 484 Automobiles—Paint coating
QC/T 625 Metallic coatings and conversion coatings for automobile
3 Terms, definitions, symbols and descriptions
For the purposes of this standard, the terms, definitions, symbols and descriptions given in GB/T 1805 and Table 1 apply.
Contents
Foreword I
1 Scope
2 Normative references
3 Terms, definitions, symbols and descriptions
4 Types
5 Designation
6 Technical requirements
7 Test methods
8 Inspection rules
9 Marking, packaging, transport, and storage
GB 25751-2010 Compression gas spring technical specification
1 Scope
This standard specifies the terms and definitions, designation, technical requirements, test methods and inspection rules for compression gas springs (hereinafter referred to as “gas springs”), as well as requirements for their marking, packaging, transport and storage, among other matters.
This standard is applicable to gas springs that use nitrogen or other inert gases as the working medium for energy storage.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 1771 Paints and varnishes—Determination of resistance to neutral salt spray (fog) (GB/T 1771—2007, ISO 7253:1996, IDT)
GB/T 1800.1 Geometrical product specifications (GPS)—Limits and fits—Part 1: Bases of tolerances, deviations and fits (GB/T 1800.1—2009, ISO 286-1:1988, MOD)
GB/T 1805 Nomenclature of springs
GB/T 2348 Fluid power systems and components—Cylinder bores and piston rod diameters (GB/T 2348—1993, neq ISO 3320:1987)
GB/T 2349 Fluid power systems and components—Cylinders—Basic series of piston strokes
GB/T 2828.1 Sampling procedures for inspection by attributes—Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1—2003, ISO 2859-1:1999, IDT)
GB/T 2829 Sampling procedures and tables for periodic inspection by attributes (apply to inspection of process stability)
GB/T 10125 Corrosion tests in artificial atmospheres—Salt spray tests (GB/T 10125—1997, eqv ISO 9227:1990)
QC/T 484 Automobiles—Paint coating
QC/T 625 Metallic coatings and conversion coatings for automobile
3 Terms, definitions, symbols and descriptions
For the purposes of this standard, the terms, definitions, symbols and descriptions given in GB/T 1805 and Table 1 apply.
Contents of GB 25751-2010
Contents
Foreword I
1 Scope
2 Normative references
3 Terms, definitions, symbols and descriptions
4 Types
5 Designation
6 Technical requirements
7 Test methods
8 Inspection rules
9 Marking, packaging, transport, and storage