1 Scope
This standard specifies rim contour shapes and dimensions for industrial vehicles.
This Standard is applicable to the rims for pneumatic tyres of industrial vehicles.
2 Normative References
The following standards contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.
GB/T 2933 Wheels and Rims for Pneumatic Tyres-Vocabulary, Designation and Marking
3 Terms and Definitions
The terms and definitions established in GB/T 2933 are applicable to this standard.
4 Rim Contour Shape and Dimension
4.1 Type 2.10, C, D, E, F, G and I Divided Rim Contours (DT)
Contents
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Rim Contour Shape and Dimension
4.1 Type 2.10, C, D, E, F, G and I Divided Rim Contours (DT)
4.2 Type 5-3.00SP Divided Rim Contour (DT)
4.3 Type 4.33R Divided Rim Contour (DT)
4.4 Type 5.00S Divided Rim Contour (DT)
4.5 Type C and E Drop Center Rim Contours (5° DC)
4.6 Semi-drop Center Rim Contour (SDC)
4.7 Flat Base Rim Contour (FB)
4.8 Type S, T, V and WI Flat Base Rim Contours (FB)
4.9 Type 4.33R Flat Base Rim Contour Shape and Dimension (FB)
4.10 5° Flat Base Rim Contour (5°FB)
4.11 Full Tapered Bead Seat Rim Contour (TB)
Appendix A (Informative) Technical Differences and Their Reasons Between this Standard and JATMA
Appendix B (Informative) Rim Contour Measure
Appendix C (Informative) Seal Ring Groove and O-ring of Rim without Inner Tube
1 Scope
This standard specifies rim contour shapes and dimensions for industrial vehicles.
This Standard is applicable to the rims for pneumatic tyres of industrial vehicles.
2 Normative References
The following standards contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.
GB/T 2933 Wheels and Rims for Pneumatic Tyres-Vocabulary, Designation and Marking
3 Terms and Definitions
The terms and definitions established in GB/T 2933 are applicable to this standard.
4 Rim Contour Shape and Dimension
4.1 Type 2.10, C, D, E, F, G and I Divided Rim Contours (DT)
Contents of GB/T 12939-2002
Contents
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Rim Contour Shape and Dimension
4.1 Type 2.10, C, D, E, F, G and I Divided Rim Contours (DT)
4.2 Type 5-3.00SP Divided Rim Contour (DT)
4.3 Type 4.33R Divided Rim Contour (DT)
4.4 Type 5.00S Divided Rim Contour (DT)
4.5 Type C and E Drop Center Rim Contours (5° DC)
4.6 Semi-drop Center Rim Contour (SDC)
4.7 Flat Base Rim Contour (FB)
4.8 Type S, T, V and WI Flat Base Rim Contours (FB)
4.9 Type 4.33R Flat Base Rim Contour Shape and Dimension (FB)
4.10 5° Flat Base Rim Contour (5°FB)
4.11 Full Tapered Bead Seat Rim Contour (TB)
Appendix A (Informative) Technical Differences and Their Reasons Between this Standard and JATMA
Appendix B (Informative) Rim Contour Measure
Appendix C (Informative) Seal Ring Groove and O-ring of Rim without Inner Tube
