1 Scope
This standard specifies requirements, test methods, inspection rules, marking, packaging, storage and preservation of parking distance monitoring and warning device for motorvehicle (hereinafter referred to as distance monitoring & warning device).
The distance monitoring & warning device cannot replace a driver to park automatically and is not a device sending alarm to personnel or things in the parking area. The device is regarded as an additional aid to the vehicle driver when parking, but it does not relieve the driver of his special responsibility when parking.
This standard is applicable to motorvehicles of Categories M and N.
Note: The functional requirements of this standard are specified based on the use of ultrasonic sensor technology. With the development of other sensor technologies, the possibility of modifying the functional requirements cannot be excluded.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition applies.
GB/T 2423.17 Basic environmental testing procedures for electric and electronic products Test Ka: Salt mist (GB/T 2423.17-1993, eqv IEC 68-2-11: 1981)
GB/T 2423.22 Environmental testing for electric and electronic products - Part 2: Test methods - Test N: Change of temperature (GB/T 2423.22-2002, IEC 60068-2-14:1984, IDT)
GB/T 2828.1 Sampling procedures for inspection by attributes – Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1-2003, ISO 2859-1: 1999, IDT)
GB/T 4942.2 Degrees of protection provided by enclosures for low-voltage apparatus (GB/T 4942.2-1993, eqv IEC 947-1: 1988)
GB/T 17619 Limits and methods of testing for immunity of electrical/electronic sub-assemblies in vehicles to electromagnetic radiation
GB 18655 Vehicles boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers (GB 18655-2002, idt IEC/CISPR 25: 1995)
GB/T 21437.2 Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only (GB/T 21437.2-2008, ISO 7637-2: 2004, IDT)
QC/T 413-2002 Basic technical requirements for automotive electric equipment
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Model designation rule
4.1 Product code
4.2 Classification code
4.3 Group code
4.4 Design No.
4.5 Model variation code
5 Requirements
5.1 General requirements
5.2 Structure
5.3 Function requirements
5.4 Protective performance
5.5 Abnormal power supply voltage resistance performance
5.6 Electromagnetic compatibility
5.7 Temperature resistance
5.8 Vibration resistance
5.9 Salt spray resistance
5.10 Temperature and humidity cycling resistance
6 Test method
6.1 Structure detection
6.2 Function detection
6.3 Protective performance test
6.4 Abnormal power supply voltage resistance test
6.5 Electromagnetic compatibility test
6.6 Temperature resistance test
6.7 Vibration resistance test
6.8 Salt spray resistance test
6.9 Temperature and humidity cycling resistance test
7 Inspection rules
7.1 Certified document and marking
7.2 Inspection categories
7.3 End-of-manufacturing inspection
7.4 Type inspection
7.5 Acceptance inspection
8 Marking, packing, storage and preservation
1 Scope
This standard specifies requirements, test methods, inspection rules, marking, packaging, storage and preservation of parking distance monitoring and warning device for motorvehicle (hereinafter referred to as distance monitoring & warning device).
The distance monitoring & warning device cannot replace a driver to park automatically and is not a device sending alarm to personnel or things in the parking area. The device is regarded as an additional aid to the vehicle driver when parking, but it does not relieve the driver of his special responsibility when parking.
This standard is applicable to motorvehicles of Categories M and N.
Note: The functional requirements of this standard are specified based on the use of ultrasonic sensor technology. With the development of other sensor technologies, the possibility of modifying the functional requirements cannot be excluded.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition applies.
GB/T 2423.17 Basic environmental testing procedures for electric and electronic products Test Ka: Salt mist (GB/T 2423.17-1993, eqv IEC 68-2-11: 1981)
GB/T 2423.22 Environmental testing for electric and electronic products - Part 2: Test methods - Test N: Change of temperature (GB/T 2423.22-2002, IEC 60068-2-14:1984, IDT)
GB/T 2828.1 Sampling procedures for inspection by attributes – Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1-2003, ISO 2859-1: 1999, IDT)
GB/T 4942.2 Degrees of protection provided by enclosures for low-voltage apparatus (GB/T 4942.2-1993, eqv IEC 947-1: 1988)
GB/T 17619 Limits and methods of testing for immunity of electrical/electronic sub-assemblies in vehicles to electromagnetic radiation
GB 18655 Vehicles boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers (GB 18655-2002, idt IEC/CISPR 25: 1995)
GB/T 21437.2 Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only (GB/T 21437.2-2008, ISO 7637-2: 2004, IDT)
QC/T 413-2002 Basic technical requirements for automotive electric equipment
Contents of GB/T 21436-2008
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Model designation rule
4.1 Product code
4.2 Classification code
4.3 Group code
4.4 Design No.
4.5 Model variation code
5 Requirements
5.1 General requirements
5.2 Structure
5.3 Function requirements
5.4 Protective performance
5.5 Abnormal power supply voltage resistance performance
5.6 Electromagnetic compatibility
5.7 Temperature resistance
5.8 Vibration resistance
5.9 Salt spray resistance
5.10 Temperature and humidity cycling resistance
6 Test method
6.1 Structure detection
6.2 Function detection
6.3 Protective performance test
6.4 Abnormal power supply voltage resistance test
6.5 Electromagnetic compatibility test
6.6 Temperature resistance test
6.7 Vibration resistance test
6.8 Salt spray resistance test
6.9 Temperature and humidity cycling resistance test
7 Inspection rules
7.1 Certified document and marking
7.2 Inspection categories
7.3 End-of-manufacturing inspection
7.4 Type inspection
7.5 Acceptance inspection
8 Marking, packing, storage and preservation
