Test method for bunk bed structure safety
1 Scope
This document describes the conditions, equipment, steps and test report of the test of bunk bed structure safety.
This document is applicable to well-installed beds with bed surface height ≥ 600 mm from the ground.
The loads and forces used in the strength and durability tests specified in this document are applicable to beds with an interior length greater than 1,400 mm and a width less than or equal to 1,200 mm.
This document is not applicable to furniture (such as cabinet racks, tables, chairs and stools) below the bed surface with a height ≥ 600 mm from the ground.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 10807-2006 Flexible cellular polymeric materials - Determination of hardness (indentation technique)
3 Terms and definitions
No terms and definitions are listed in this document.
4 General test conditions
4.1 Tolerances regarding the test
Unless otherwise specified, the following tolerances apply:
——The tolerance of all forces shall be ±5% of the nominal force;
——The tolerance of all masses shall be ±1% of the nominal mass;
——For all dimensions less than 200 mm, the deviation shall be ±1 mm of the nominal dimensions; the deviation for other dimensions shall be ±0.5%; the dimensional deviation for 300 mm spherical radius of curvature in impact head (see 5.3.3) and loading pad (see 5.4.1) shall be ±5 mm;
——The deviation between the loading position of the loading pad and that of the impact head shall be ±5 mm.
Note: It is considered that the test results are not adversely affected if the tolerances mentioned above are met.
In the process of loading, the force value may be replaced by the mass of the weight. The relationship of 10 N=1 kg shall be used for conversion.
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 General test conditions
4.1 Tolerances regarding the test
4.2 Initial preparation for test
5 Test equipment
5.1 General requirements
5.2 Measuring cone heads
5.3 Bed surface impactor
5.4 Loading pad
5.5 Soft cushion for test
5.6 Test load
5.7 Stops
5.8 Test ground (bench) surface
5.9 Footrest impactor
5.10 V-shaped opening template
5.11 Foam board (spongy cushion)
6 Test steps
6.1 Installation and inspection before test
6.2 Inspection of processing technology
6.3 Measurement of the clearance of holes, gaps and openings
6.4 Strength, durability and stability tests
7 Test report
Test method for bunk bed structure safety
1 Scope
This document describes the conditions, equipment, steps and test report of the test of bunk bed structure safety.
This document is applicable to well-installed beds with bed surface height ≥ 600 mm from the ground.
The loads and forces used in the strength and durability tests specified in this document are applicable to beds with an interior length greater than 1,400 mm and a width less than or equal to 1,200 mm.
This document is not applicable to furniture (such as cabinet racks, tables, chairs and stools) below the bed surface with a height ≥ 600 mm from the ground.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 10807-2006 Flexible cellular polymeric materials - Determination of hardness (indentation technique)
3 Terms and definitions
No terms and definitions are listed in this document.
4 General test conditions
4.1 Tolerances regarding the test
Unless otherwise specified, the following tolerances apply:
——The tolerance of all forces shall be ±5% of the nominal force;
——The tolerance of all masses shall be ±1% of the nominal mass;
——For all dimensions less than 200 mm, the deviation shall be ±1 mm of the nominal dimensions; the deviation for other dimensions shall be ±0.5%; the dimensional deviation for 300 mm spherical radius of curvature in impact head (see 5.3.3) and loading pad (see 5.4.1) shall be ±5 mm;
——The deviation between the loading position of the loading pad and that of the impact head shall be ±5 mm.
Note: It is considered that the test results are not adversely affected if the tolerances mentioned above are met.
In the process of loading, the force value may be replaced by the mass of the weight. The relationship of 10 N=1 kg shall be used for conversion.
Contents of GB/T 24430-2023
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 General test conditions
4.1 Tolerances regarding the test
4.2 Initial preparation for test
5 Test equipment
5.1 General requirements
5.2 Measuring cone heads
5.3 Bed surface impactor
5.4 Loading pad
5.5 Soft cushion for test
5.6 Test load
5.7 Stops
5.8 Test ground (bench) surface
5.9 Footrest impactor
5.10 V-shaped opening template
5.11 Foam board (spongy cushion)
6 Test steps
6.1 Installation and inspection before test
6.2 Inspection of processing technology
6.3 Measurement of the clearance of holes, gaps and openings
6.4 Strength, durability and stability tests
7 Test report
