Foreword
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This document is developed in accordance with the rules given in GB/T 1.1-2020 Directives for standardization - Part 1: Rules for the structure and drafting of standardizing documents.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The issuing body of this document shall not be held responsible for identifying any or all such patent rights.
This document was proposed by the China National Light Industry Council.
This document is under the jurisdiction of SAC/TC 48 National Technical Committee on Plastic Products of Standardization Administration of China.
Protective polyethylene gloves for daily use
1 Scope
This document specifies the classification, requirements, inspection rules, marking, packaging, transport and storage of protective polyethylene gloves for daily use (hereinafter referred to as “gloves”) and provides the test methods.
This document is applicable to the production, inspection and sales of protective gloves made through pressing and heat sealing processes with polyethylene film produced by blow molding or casting as the main raw material.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 1040.1-2018 Plastics - Determination of tensile properties - Part 1: General principles
GB/T 1040.3-2006 Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 2918-2018 Plastics - Standard atmospheres for conditioning and testing
GB/T 3920-2008 Textiles - Tests for colour fastness - Colour fastness to rubbing
GB/T 9345.1-2008 Plastics - Determination of ash - Part 1: General methods
GB/T 16276-1996 Test method for blocking of plastic film
QB/T 5787-2022 Test method for rubbing resistance of plastic film
3 Terms and definitions
No terms and definitions are listed in this document.
4 Classification
4.1 Gloves are divided into high density polyethylene (PE-HD) gloves and low density polyethylene (PE-LD) gloves according to the main materials.
4.2 Gloves are divided into smooth type and embossed type according to whether they are embossed.
4.3 Gloves are divided into ordinary type and leakage-proof type according to whether they are leakage-proof.
Foreword ii
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Technical requirements
6 Test methods
7 Inspection rules
8 Marking, packaging, transport and storage
Annex A (normative) Bursting strength test method
Foreword
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This document is developed in accordance with the rules given in GB/T 1.1-2020 Directives for standardization - Part 1: Rules for the structure and drafting of standardizing documents.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The issuing body of this document shall not be held responsible for identifying any or all such patent rights.
This document was proposed by the China National Light Industry Council.
This document is under the jurisdiction of SAC/TC 48 National Technical Committee on Plastic Products of Standardization Administration of China.
Protective polyethylene gloves for daily use
1 Scope
This document specifies the classification, requirements, inspection rules, marking, packaging, transport and storage of protective polyethylene gloves for daily use (hereinafter referred to as “gloves”) and provides the test methods.
This document is applicable to the production, inspection and sales of protective gloves made through pressing and heat sealing processes with polyethylene film produced by blow molding or casting as the main raw material.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 1040.1-2018 Plastics - Determination of tensile properties - Part 1: General principles
GB/T 1040.3-2006 Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 2918-2018 Plastics - Standard atmospheres for conditioning and testing
GB/T 3920-2008 Textiles - Tests for colour fastness - Colour fastness to rubbing
GB/T 9345.1-2008 Plastics - Determination of ash - Part 1: General methods
GB/T 16276-1996 Test method for blocking of plastic film
QB/T 5787-2022 Test method for rubbing resistance of plastic film
3 Terms and definitions
No terms and definitions are listed in this document.
4 Classification
4.1 Gloves are divided into high density polyethylene (PE-HD) gloves and low density polyethylene (PE-LD) gloves according to the main materials.
4.2 Gloves are divided into smooth type and embossed type according to whether they are embossed.
4.3 Gloves are divided into ordinary type and leakage-proof type according to whether they are leakage-proof.
Contents of GB/T 42948-2023
Foreword ii
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Technical requirements
6 Test methods
7 Inspection rules
8 Marking, packaging, transport and storage
Annex A (normative) Bursting strength test method
