GB/T 44993-2024 On-site testing instruments of off-board charger for electric vehicles
1 Scope
This document specifies the terms and definitions, technical requirements, test methods, inspection rules as well as packaging, transportation and storage of on-site testing instruments of off-board charger for electric vehicles.
This document is applicable to the design, manufacture, procurement and acceptance of on-site testing instruments of off-board chargers of 1,000V and below.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.1-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold
GB/T 2423.2-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Tests B: Dry heat
GB/T 2423.4-2008 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12h+12h cycle)
GB/T 2423.5-2019 Environmental testing - Part 2: Test methods - Test Ea and guidance: Shock
GB/T 2423.43-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Mounting of specimens for vibration, impact and similar dynamic tests
GB/T 2423.56-2023 Environmental testing - Part 2: Test methods - Test Fh: Vibration, broadband random and guidance
GB/T 4208-2017 Degrees of protection provided by enclosure (IP code)
GB 4824-2019 Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
GB/T 5169.11-2017 Fire hazard testing for electric and electronic products - Part 11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
GB/T 13384-2008 General specifications for packing of mechanical and electrical product
GB/T 18268.1-2010 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements
GB/T 18487.1-2023 Electric vehicle conductive charging system - Part 1: General requirements
GB/T 20234.3-2023 Connection set for conductive charging of electric vehicles - Part 3: DC charging coupler
GB/T 29317-2021 Terminology of electric vehicle charging/battery swap infrastructure
NB/T 33001-2018 Specification for electric vehicle off-board conductive charger
3 Terms and definitions
For the purpose of this document, the terms and definitions given in GB/T 18487.1-2023, GB/T 29317-2021, NB/T 33001-2018 and the following apply.
3.1
off-board charger for electric vehicle
special device, fixedly connected to AC or DC power supply and converting the electric energy to DC electric energy, that charges the swappable battery system of electric vehicle by conduction
Note: Hereinafter referred to as an "off-board charger".
[Source: GB/T 29317-2021, 5.1, modified]
3.2
on-site testing instruments of off-board charger for electric vehicle
device for on-site testing parameters such as energy error of off-board charger
Note: Hereinafter referred to as "testing instrument", of which the principle block diagram is shown in Annex A.
4 Technical requirements
4.1 Environmental conditions
The environmental conditions for normal use of the testing instrument shall meet the following conditions:
a) ambient temperature: -25℃~55℃;
b) ambient humidity: with a relative humidity of not greater than 95%;
c) the altitude shall not be higher than 2,000m;
d) in special environmental conditions, it is necessary to consult with the manufacturer of the testing instrument to confirm or take appropriate measures.
4.2 Structure and mechanical properties
4.2.1 Impact
The testing instrument, after subjecting the shell to the impact test in 5.2.1, shall be intact in appearance, and the measurement performance shall meet the requirements of 4.5.
4.2.2 Vibration
The testing instrument, after being subjected to the vibration test in 5.2.2, shall be intact in appearance, and the measurement performance shall meet the requirements of 4.5.
4.2.3 Resistance to heat and flame
The testing instrument shall withstand the hot wire test at 750℃; and the test result shall meet the requirements of GB/T 5169.11-2017, Clause 10.
4.2.4 Degree of protection
The degree of protection of the testing instrument shall not be inferior to the requirements for IP30 in GB/T 4208-2017.
4.2.5 Earthing terminal
The testing instrument shall have a protective earthing terminal with obvious earthing mark, and have a reliable electrical connection with the metal shell accessible to the testing instrument, with the resistance between the earthing terminal and each connection point of not greater than 0.1Ω.
4.2.6 Marking
The nameplate of the testing instrument shall be provided with at least the following markings:
a) product name;
b) manufacturer name and trademark;
c) accuracy class;
d) measuring range;
e) product model;
f) delivery time and No.;
g) rated supply voltage parameters.
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
4.1 Environmental conditions
4.2 Structure and mechanical properties
4.3 Electrical properties
4.4 Electromagnetic compatibility
4.5 Measurement performance
4.6 Interface performance
5 Test method
5.1 Environmental performance
5.2 Structural and mechanical properties
5.3 Electrical properties
5.4 Electromagnetic compatibility
5.5 Measurement performance
5.6 Interface performance
6 Inspection rules
6.1 Inspection classification
6.2 Type inspection
6.3 End-of-manufacturing inspection
6.4 Full inspection acceptance test
7 Packaging, transportation and storage
7.1 Packaging
7.2 Transportation
7.3 Storage
Annex A (Informative) Principal block diagram of the testing instrument
Figure A.1 Principal block diagram of the testing instrument
Table 1 Electrical energy error limit
Table 2 Test standard deviation limits for electrical energy measurements
Table 3 Limits of error change due to influence quantity
Table 4 Test voltage for insulation test
Table 5 Test voltage for dielectric strength
Table 6 Reference conditions
Table 7 Test items of testing instrument
GB/T 44993-2024 On-site testing instruments of off-board charger for electric vehicles
1 Scope
This document specifies the terms and definitions, technical requirements, test methods, inspection rules as well as packaging, transportation and storage of on-site testing instruments of off-board charger for electric vehicles.
This document is applicable to the design, manufacture, procurement and acceptance of on-site testing instruments of off-board chargers of 1,000V and below.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.1-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold
GB/T 2423.2-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Tests B: Dry heat
GB/T 2423.4-2008 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12h+12h cycle)
GB/T 2423.5-2019 Environmental testing - Part 2: Test methods - Test Ea and guidance: Shock
GB/T 2423.43-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Mounting of specimens for vibration, impact and similar dynamic tests
GB/T 2423.56-2023 Environmental testing - Part 2: Test methods - Test Fh: Vibration, broadband random and guidance
GB/T 4208-2017 Degrees of protection provided by enclosure (IP code)
GB 4824-2019 Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
GB/T 5169.11-2017 Fire hazard testing for electric and electronic products - Part 11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
GB/T 13384-2008 General specifications for packing of mechanical and electrical product
GB/T 18268.1-2010 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements
GB/T 18487.1-2023 Electric vehicle conductive charging system - Part 1: General requirements
GB/T 20234.3-2023 Connection set for conductive charging of electric vehicles - Part 3: DC charging coupler
GB/T 29317-2021 Terminology of electric vehicle charging/battery swap infrastructure
NB/T 33001-2018 Specification for electric vehicle off-board conductive charger
3 Terms and definitions
For the purpose of this document, the terms and definitions given in GB/T 18487.1-2023, GB/T 29317-2021, NB/T 33001-2018 and the following apply.
3.1
off-board charger for electric vehicle
special device, fixedly connected to AC or DC power supply and converting the electric energy to DC electric energy, that charges the swappable battery system of electric vehicle by conduction
Note: Hereinafter referred to as an "off-board charger".
[Source: GB/T 29317-2021, 5.1, modified]
3.2
on-site testing instruments of off-board charger for electric vehicle
device for on-site testing parameters such as energy error of off-board charger
Note: Hereinafter referred to as "testing instrument", of which the principle block diagram is shown in Annex A.
4 Technical requirements
4.1 Environmental conditions
The environmental conditions for normal use of the testing instrument shall meet the following conditions:
a) ambient temperature: -25℃~55℃;
b) ambient humidity: with a relative humidity of not greater than 95%;
c) the altitude shall not be higher than 2,000m;
d) in special environmental conditions, it is necessary to consult with the manufacturer of the testing instrument to confirm or take appropriate measures.
4.2 Structure and mechanical properties
4.2.1 Impact
The testing instrument, after subjecting the shell to the impact test in 5.2.1, shall be intact in appearance, and the measurement performance shall meet the requirements of 4.5.
4.2.2 Vibration
The testing instrument, after being subjected to the vibration test in 5.2.2, shall be intact in appearance, and the measurement performance shall meet the requirements of 4.5.
4.2.3 Resistance to heat and flame
The testing instrument shall withstand the hot wire test at 750℃; and the test result shall meet the requirements of GB/T 5169.11-2017, Clause 10.
4.2.4 Degree of protection
The degree of protection of the testing instrument shall not be inferior to the requirements for IP30 in GB/T 4208-2017.
4.2.5 Earthing terminal
The testing instrument shall have a protective earthing terminal with obvious earthing mark, and have a reliable electrical connection with the metal shell accessible to the testing instrument, with the resistance between the earthing terminal and each connection point of not greater than 0.1Ω.
4.2.6 Marking
The nameplate of the testing instrument shall be provided with at least the following markings:
a) product name;
b) manufacturer name and trademark;
c) accuracy class;
d) measuring range;
e) product model;
f) delivery time and No.;
g) rated supply voltage parameters.
Contents of GB/T 44993-2024
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
4.1 Environmental conditions
4.2 Structure and mechanical properties
4.3 Electrical properties
4.4 Electromagnetic compatibility
4.5 Measurement performance
4.6 Interface performance
5 Test method
5.1 Environmental performance
5.2 Structural and mechanical properties
5.3 Electrical properties
5.4 Electromagnetic compatibility
5.5 Measurement performance
5.6 Interface performance
6 Inspection rules
6.1 Inspection classification
6.2 Type inspection
6.3 End-of-manufacturing inspection
6.4 Full inspection acceptance test
7 Packaging, transportation and storage
7.1 Packaging
7.2 Transportation
7.3 Storage
Annex A (Informative) Principal block diagram of the testing instrument
Figure A.1 Principal block diagram of the testing instrument
Table 1 Electrical energy error limit
Table 2 Test standard deviation limits for electrical energy measurements
Table 3 Limits of error change due to influence quantity
Table 4 Test voltage for insulation test
Table 5 Test voltage for dielectric strength
Table 6 Reference conditions
Table 7 Test items of testing instrument
