GB/T 4857 consists of the following parts under the general title Packaging - Basic tests for transport packages:
——Part 1: Identification of parts when testing;
——Part 2: Temperature and humidity conditioning;
——Part 3: Stacking test methods using a static load;
——Part 4: Compression and stacking test using compression tester;
——Part 5: Vertical impact test method by dropping;
——Part 6: Rolling test method;
——Part 7: Sinusoidal vibration test method at constant frequency;
——Part 9: Water spray test;
——Part 10: Sinusoidal vibration test method using at variable vibration frequency;
——Part 11: Horizontal impact test methods;
——Part 12: Water immersion test method;
——Part 13: Low pressure test;
——Part 14: Toppling test method;
——Part 15: Controlled horizontal impact test method;
——Part 17: General principles for the compilation of performance test;
——Part 19: Information to be recorded in distribution trials;
——Part 20: Bump test method;
——Part 22: Unit loads stability test methods;
——Part 23: Random vibration test method.
This is Part 1 of GB/T 4857.
Packaging - Basic tests for transport packages - Part 1: Identification of parts when testing
1 Scope
This part of GB/T 4857 specifies identification of parts of transport packages (hereinafter referred to as package) when testing.
This part is applicable to the identification of parts of packages, and may also serve as reference for the identification of parts of packaging containers.
2 Identification
2.1 Parallelepipedal packages
2.1.1 The package shall be placed in the position in which it is intended to be transported. If the transport position is not known, the package shall be placed in the most stable state. After placing, if there are joints perpendicular to the surface on the package, any joint of the package shall be placed vertically on the observer’s right; when the joint is parallel to the surface or there is no joint, any smaller end of the package shall face the observer. The identification is shown in Figure 1.
GB/T 4857 consists of the following parts under the general title Packaging - Basic tests for transport packages:
——Part 1: Identification of parts when testing;
——Part 2: Temperature and humidity conditioning;
——Part 3: Stacking test methods using a static load;
——Part 4: Compression and stacking test using compression tester;
——Part 5: Vertical impact test method by dropping;
——Part 6: Rolling test method;
——Part 7: Sinusoidal vibration test method at constant frequency;
——Part 9: Water spray test;
——Part 10: Sinusoidal vibration test method using at variable vibration frequency;
——Part 11: Horizontal impact test methods;
——Part 12: Water immersion test method;
——Part 13: Low pressure test;
——Part 14: Toppling test method;
——Part 15: Controlled horizontal impact test method;
——Part 17: General principles for the compilation of performance test;
——Part 19: Information to be recorded in distribution trials;
——Part 20: Bump test method;
——Part 22: Unit loads stability test methods;
——Part 23: Random vibration test method.
This is Part 1 of GB/T 4857.
Packaging - Basic tests for transport packages - Part 1: Identification of parts when testing
1 Scope
This part of GB/T 4857 specifies identification of parts of transport packages (hereinafter referred to as package) when testing.
This part is applicable to the identification of parts of packages, and may also serve as reference for the identification of parts of packaging containers.
2 Identification
2.1 Parallelepipedal packages
2.1.1 The package shall be placed in the position in which it is intended to be transported. If the transport position is not known, the package shall be placed in the most stable state. After placing, if there are joints perpendicular to the surface on the package, any joint of the package shall be placed vertically on the observer’s right; when the joint is parallel to the surface or there is no joint, any smaller end of the package shall face the observer. The identification is shown in Figure 1.
