GB/T 5132 consists of the following parts, under the general title Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes:
— Part 1: General Requirements;
— Part 2: Test Methods;
— Part 3: Round Laminated Rolled Tubes;
— Part 4: Round Laminated Moulded Tubes;
— Part 5: Round Laminated Moulded Rods;
This part is Part 5 of GB/T 5132.
Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes — Part 5: Round Laminated Moulded Rods
1 Scope
This part of GB/T 5132 specifies requirements for industrial rigid round laminated moulded rods for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties of moulded rods are given in Table 1.
This part is applicable to industrial rigid round laminated rods based on thermosetting resins for electrical purpose.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of GB/T 5132. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However, parties to agreements based on this part are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 5132.1-2009 Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes — Part 1: General Requirements (IEC 61212-1:2006, IDT)
GB/T 5132.2-2009 Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes — Part 2: Methods of Test (IEC 61212-2:2006, IDT)
ISO 472 Plastics — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
3. 1
round laminated moulded rod (as applied to thermosets)
rod formed by rolling impregnated layers of material on a mandrel, removing the mandrel, curing in a cylindrical mould under heat and pressure, and grinding to size
Foreword II
1 Scope
2 Normative References
3 Terms and definitions
4 Designations and Classification
5 Requirements
GB/T 5132 consists of the following parts, under the general title Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes:
— Part 1: General Requirements;
— Part 2: Test Methods;
— Part 3: Round Laminated Rolled Tubes;
— Part 4: Round Laminated Moulded Tubes;
— Part 5: Round Laminated Moulded Rods;
This part is Part 5 of GB/T 5132.
Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes — Part 5: Round Laminated Moulded Rods
1 Scope
This part of GB/T 5132 specifies requirements for industrial rigid round laminated moulded rods for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties of moulded rods are given in Table 1.
This part is applicable to industrial rigid round laminated rods based on thermosetting resins for electrical purpose.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of GB/T 5132. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However, parties to agreements based on this part are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 5132.1-2009 Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes — Part 1: General Requirements (IEC 61212-1:2006, IDT)
GB/T 5132.2-2009 Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes — Part 2: Methods of Test (IEC 61212-2:2006, IDT)
ISO 472 Plastics — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
3. 1
round laminated moulded rod (as applied to thermosets)
rod formed by rolling impregnated layers of material on a mandrel, removing the mandrel, curing in a cylindrical mould under heat and pressure, and grinding to size
Contents of GB/T 5132.5-2009
Foreword II
1 Scope
2 Normative References
3 Terms and definitions
4 Designations and Classification
5 Requirements
