GB/T 585-2026 Marine cast steel flanged stop check valves English, Anglais, Englisch, Inglés, えいご
This is a draft translation for reference among interesting stakeholders. The finalized translation (passing through draft translation, self-check, revision and verification) will be delivered upon being ordered.
ICS
CCS
National Standard of the People's Republic of China
GB/T 585-2026
Marine cast steel flanged stop check valves
船用法兰铸钢截止止回阀
Issue date: 2026-09-28 Implementation date: 2027-01-01
Issued by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
the Standardization Administration of the People's Republic of China
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and marking
5 Requirements
6 Test methods
7 Inspection rules
Marine cast steel globe stop-check valves
1 Scope
This document specifies the classification and marking, requirements, test methods, inspection rules, and packaging and storage of marine cast steel globe stop-check valves (hereinafter referred to as "stop-check valves").
This document is applicable to the design, manufacture and acceptance of stop-check valves used in marine piping systems.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 600—2023, General technical requirements for marine piping valves
GB/T 699—2015, High-quality carbon structural steels
GB/T 898—1988, Double-end studs, *b*m = 1.25 *d*
GB/T 983—2012, Stainless steel covered electrodes
GB/T 1220—2007, Stainless steel bars
GB/T 1958, Geometrical product specifications (GPS) — Geometrical tolerance — Verification
GB/T 3032, Marking of marine valves and piping accessories
GB/T 6170—2015, Hexagon nuts, style 1
GB/T 9124.1—2019, Steel pipe flanges — Part 1: PN series
GB/T 11698—2026, Length of structural members between flanged pipe connections for marine use
GB/T 12229—2025, General valves — Technical conditions for carbon steel castings
CB/T 3530—1993, Handwheels for piping accessories
CB/T 3589—1994, Non-asbestos gasket and packing for marine valves
CB/T 4196—2011, Marine valve flange — Connection dimensions and sealing surfaces
JB/T 6626—2011, Polytetrafluoroethylene braided packings
QB/T 4041—2010, Polytetrafluoroethylene sheets
3 Terms and definitions
No terms and definitions are required to be defined in this document.
4 Classification and marking
4.1 Types
The types of stop-check valves are specified as follows:
a) Type A: Straight-through stop-check valve whose flange connection dimensions and sealing surfaces comply with CB/T 4196—2011;
b) Type B: Right-angle stop-check valve whose flange connection dimensions and sealing surfaces comply with CB/T 4196—2011;
c) Type AS: Straight-through stop-check valve whose flange connection dimensions and sealing surfaces comply with GB/T 9124.1—2019;
d) Type BS: Right-angle stop-check valve whose flange connection dimensions and sealing surfaces comply with GB/T 9124.1—2019.
4.2 Basic parameters
The basic parameters of the stop-check valves are given in Table 1.
Table 1 — Basic parameters of stop-check valves
4.3 Structure and basic dimensions
4.3.1 The structures of Type A and Type B stop-check valves for sizes DN15 to DN150 of PN10, PN16 and PN25 are shown in Figure 1, and the basic dimensions are given in Table 2.
...
5 Requirements
5.1 Materials
5.1.1 The materials for the main parts of the stop-check valve shall comply with the provisions of Table 6. Production may commence only after the materials have been inspected and found to be qualified.
...
6 Test methods
6.1 Strength
Carried out in accordance with the provisions of 5.1.1.2 in GB/T 600—2023.
6.2 Tightness
Carried out in accordance with the provisions of 5.1.2.2 in GB/T 600—2023.
6.3 Dimensions and dimensional tolerances
6.3.1 Wall thickness and wall thickness tolerances shall be inspected with measuring instruments such as thickness gauges, calipers, steel rulers, or instruments of equivalent accuracy.
6.3.2 Linear dimension tolerances shall be inspected with measuring instruments of equivalent accuracy.
6.3.3 Structural length tolerances shall be inspected with steel rulers, vernier calipers, or instruments of equivalent accuracy.
6.4 Geometrical tolerances
Carried out for inspection in accordance with the provisions of GB/T 1958.
6.5 Assembly
Inspected by visual inspection or with tools such as calipers of equivalent accuracy.
6.6 Appearance
Visual inspection.
6.7 Weight
The stop-check valve shall be weighed on a scale with a division value not greater than 0.01 kg.
6.8 Marking
Visual inspection.
7 Inspection rules
7.1 Classification of inspection
GB/T 585-2026 Marine cast steel flanged stop check valves English, Anglais, Englisch, Inglés, えいご
This is a draft translation for reference among interesting stakeholders. The finalized translation (passing through draft translation, self-check, revision and verification) will be delivered upon being ordered.
ICS
CCS
National Standard of the People's Republic of China
GB/T 585-2026
Marine cast steel flanged stop check valves
船用法兰铸钢截止止回阀
Issue date: 2026-09-28 Implementation date: 2027-01-01
Issued by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
the Standardization Administration of the People's Republic of China
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and marking
5 Requirements
6 Test methods
7 Inspection rules
Marine cast steel globe stop-check valves
1 Scope
This document specifies the classification and marking, requirements, test methods, inspection rules, and packaging and storage of marine cast steel globe stop-check valves (hereinafter referred to as "stop-check valves").
This document is applicable to the design, manufacture and acceptance of stop-check valves used in marine piping systems.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 600—2023, General technical requirements for marine piping valves
GB/T 699—2015, High-quality carbon structural steels
GB/T 898—1988, Double-end studs, *b*m = 1.25 *d*
GB/T 983—2012, Stainless steel covered electrodes
GB/T 1220—2007, Stainless steel bars
GB/T 1958, Geometrical product specifications (GPS) — Geometrical tolerance — Verification
GB/T 3032, Marking of marine valves and piping accessories
GB/T 6170—2015, Hexagon nuts, style 1
GB/T 9124.1—2019, Steel pipe flanges — Part 1: PN series
GB/T 11698—2026, Length of structural members between flanged pipe connections for marine use
GB/T 12229—2025, General valves — Technical conditions for carbon steel castings
CB/T 3530—1993, Handwheels for piping accessories
CB/T 3589—1994, Non-asbestos gasket and packing for marine valves
CB/T 4196—2011, Marine valve flange — Connection dimensions and sealing surfaces
JB/T 6626—2011, Polytetrafluoroethylene braided packings
QB/T 4041—2010, Polytetrafluoroethylene sheets
3 Terms and definitions
No terms and definitions are required to be defined in this document.
4 Classification and marking
4.1 Types
The types of stop-check valves are specified as follows:
a) Type A: Straight-through stop-check valve whose flange connection dimensions and sealing surfaces comply with CB/T 4196—2011;
b) Type B: Right-angle stop-check valve whose flange connection dimensions and sealing surfaces comply with CB/T 4196—2011;
c) Type AS: Straight-through stop-check valve whose flange connection dimensions and sealing surfaces comply with GB/T 9124.1—2019;
d) Type BS: Right-angle stop-check valve whose flange connection dimensions and sealing surfaces comply with GB/T 9124.1—2019.
4.2 Basic parameters
The basic parameters of the stop-check valves are given in Table 1.
Table 1 — Basic parameters of stop-check valves
4.3 Structure and basic dimensions
4.3.1 The structures of Type A and Type B stop-check valves for sizes DN15 to DN150 of PN10, PN16 and PN25 are shown in Figure 1, and the basic dimensions are given in Table 2.
...
5 Requirements
5.1 Materials
5.1.1 The materials for the main parts of the stop-check valve shall comply with the provisions of Table 6. Production may commence only after the materials have been inspected and found to be qualified.
...
6 Test methods
6.1 Strength
Carried out in accordance with the provisions of 5.1.1.2 in GB/T 600—2023.
6.2 Tightness
Carried out in accordance with the provisions of 5.1.2.2 in GB/T 600—2023.
6.3 Dimensions and dimensional tolerances
6.3.1 Wall thickness and wall thickness tolerances shall be inspected with measuring instruments such as thickness gauges, calipers, steel rulers, or instruments of equivalent accuracy.
6.3.2 Linear dimension tolerances shall be inspected with measuring instruments of equivalent accuracy.
6.3.3 Structural length tolerances shall be inspected with steel rulers, vernier calipers, or instruments of equivalent accuracy.
6.4 Geometrical tolerances
Carried out for inspection in accordance with the provisions of GB/T 1958.
6.5 Assembly
Inspected by visual inspection or with tools such as calipers of equivalent accuracy.
6.6 Appearance
Visual inspection.
6.7 Weight
The stop-check valve shall be weighed on a scale with a division value not greater than 0.01 kg.
6.8 Marking
Visual inspection.
7 Inspection rules
7.1 Classification of inspection