1 Scope
This standard specifies pylon course slalom test procedure, steering transient response test procedure (steering wheel angle step input and steering wheel angle pulse input), returnability test procedure, steering efforts test procedure, steady static circular test procedure and steering wheel central area controllability and stability test procedure for determining the controllability and stability of automobiles.
As for the controllability and stability of automobiles, the pylon course slalom test procedure, steering transient response test procedure (steering wheel angle step input and steering wheel angle pulse input), returnability test procedure and steering efforts test procedure are applicable to Categories M, N and G vehicles, the steady static circular test procedure is applicable to Categories M, N and G two-axle vehicles, the steering wheel central area controllability and stability test procedure is applicable to Categories M1 and N1 vehicles, and vehicles of other types may refer to these test procedures.
2 Normative References
The following documents for the application of this document are essential. For dated reference, only the edition cited applies. For undated references, the latest edition (including any amendment) applies to this document.
GB/T 3730.1 Motor Vehicles and Trailers - Types - Terms and Definitions
GB/T 3730.2 Road Vehicle - Masses - Vocabulary and Codes
GB/T 12534-1990 Motor Vehicles - General Rules of Road Test Method
GB/T 12549 Terms and Definitions for Vehicle Controllability and Stability
GB/T 15089 Classification of Power-driven Vehicles and Trailers
3 Apparatuses
3.1 The instruments necessary for test are as follows:
a) Speed meter;
b) Measuring instruments for steering wheel torque and angle;
c) Automobile controllability and stability tester;
d) Stopwatch;
e) Multichannel data acquisition system.
3.2 Test apparatuses shall meet the requirements of 3.5 in GB/T 12534-1990.
3.3 Measurement range and maximum error of measuring instruments shall meet those specified in Table 1.
Foreword i
1 Scope
2 Normative References
3 Apparatuses
4 Test Conditions
4.1 Test Automobile
4.2 Test Site and Environment
5 Pylon Course Slalom Test
5.1 Test Instruments
5.2 Parameters to be Measured
5.3 Test Procedures
5.4 Data Processing for Pylon Course Slalom Test
5.5 Expression of Results for Pylon Course Slalom Test
6 Steering Transient Response Test (Steering Wheel Angle Step Input)
6.1 Test Instruments
6.2 Parameters to be Measured
6.3 Test Procedures
6.4 Test Data Processing
6.5 Expression of Test Results
7 Steering Transient Response Test (Steering Wheel Angle Pulse Input)
7.1 Test Instruments
7.2 Parameters to be Measured
7.3 Test Procedures
7.4 Test Data Processing
7.5 Expression of Test Results
8 Returnability Test
8.1 Test Instruments
8.2 Parameters to be Measured
8.3 Test Procedures
8.4 Data Processing for Returnability Test
8.5 Expression of Test Results
9 Steering Efforts Test
9.1 Test Instruments
9.2 Parameters to be Measured
9.3 Test Procedures
9.4 Test Data Processing
9.5 Expression of Test Results
10 Steady Static Circular Test
10.1 Test Instruments
10.2 Parameters to be Measured
10.3 Test Procedures
10.4 Test Data Processing
10.5 Expression of Test Results
11 Steering Wheel Central Area Controllability and Stability Test
11.1 Test Instruments
11.2 Parameters to be Measured
11.3 Test Procedures
11.4 Test Data Processing
11.5 Expression of Test Results
12 Test Report
Annex A (Normative) Data Sheet——Basic Assessment Test
Annex B (Informative) Data Sheet——Benchmarking Test
Annex C (Informative) Test Conditions——Benchmarking Test
Annex D (Informative) Steady Static Circular Test Procedure—— Fixed Turning Radius Procedure
1 Scope
This standard specifies pylon course slalom test procedure, steering transient response test procedure (steering wheel angle step input and steering wheel angle pulse input), returnability test procedure, steering efforts test procedure, steady static circular test procedure and steering wheel central area controllability and stability test procedure for determining the controllability and stability of automobiles.
As for the controllability and stability of automobiles, the pylon course slalom test procedure, steering transient response test procedure (steering wheel angle step input and steering wheel angle pulse input), returnability test procedure and steering efforts test procedure are applicable to Categories M, N and G vehicles, the steady static circular test procedure is applicable to Categories M, N and G two-axle vehicles, the steering wheel central area controllability and stability test procedure is applicable to Categories M1 and N1 vehicles, and vehicles of other types may refer to these test procedures.
2 Normative References
The following documents for the application of this document are essential. For dated reference, only the edition cited applies. For undated references, the latest edition (including any amendment) applies to this document.
GB/T 3730.1 Motor Vehicles and Trailers - Types - Terms and Definitions
GB/T 3730.2 Road Vehicle - Masses - Vocabulary and Codes
GB/T 12534-1990 Motor Vehicles - General Rules of Road Test Method
GB/T 12549 Terms and Definitions for Vehicle Controllability and Stability
GB/T 15089 Classification of Power-driven Vehicles and Trailers
3 Apparatuses
3.1 The instruments necessary for test are as follows:
a) Speed meter;
b) Measuring instruments for steering wheel torque and angle;
c) Automobile controllability and stability tester;
d) Stopwatch;
e) Multichannel data acquisition system.
3.2 Test apparatuses shall meet the requirements of 3.5 in GB/T 12534-1990.
3.3 Measurement range and maximum error of measuring instruments shall meet those specified in Table 1.
Contents of GB/T 6323-2014
Foreword i
1 Scope
2 Normative References
3 Apparatuses
4 Test Conditions
4.1 Test Automobile
4.2 Test Site and Environment
5 Pylon Course Slalom Test
5.1 Test Instruments
5.2 Parameters to be Measured
5.3 Test Procedures
5.4 Data Processing for Pylon Course Slalom Test
5.5 Expression of Results for Pylon Course Slalom Test
6 Steering Transient Response Test (Steering Wheel Angle Step Input)
6.1 Test Instruments
6.2 Parameters to be Measured
6.3 Test Procedures
6.4 Test Data Processing
6.5 Expression of Test Results
7 Steering Transient Response Test (Steering Wheel Angle Pulse Input)
7.1 Test Instruments
7.2 Parameters to be Measured
7.3 Test Procedures
7.4 Test Data Processing
7.5 Expression of Test Results
8 Returnability Test
8.1 Test Instruments
8.2 Parameters to be Measured
8.3 Test Procedures
8.4 Data Processing for Returnability Test
8.5 Expression of Test Results
9 Steering Efforts Test
9.1 Test Instruments
9.2 Parameters to be Measured
9.3 Test Procedures
9.4 Test Data Processing
9.5 Expression of Test Results
10 Steady Static Circular Test
10.1 Test Instruments
10.2 Parameters to be Measured
10.3 Test Procedures
10.4 Test Data Processing
10.5 Expression of Test Results
11 Steering Wheel Central Area Controllability and Stability Test
11.1 Test Instruments
11.2 Parameters to be Measured
11.3 Test Procedures
11.4 Test Data Processing
11.5 Expression of Test Results
12 Test Report
Annex A (Normative) Data Sheet——Basic Assessment Test
Annex B (Informative) Data Sheet——Benchmarking Test
Annex C (Informative) Test Conditions——Benchmarking Test
Annex D (Informative) Steady Static Circular Test Procedure—— Fixed Turning Radius Procedure
