This standard specifies the type, basic parameters and main dimensions, requirements, markings and examples, assembly, labels, packing, transportation and storage of drive for glass-lined vessel with agitator.
This standard is applicable to drive for glass-lined vessel with agitator.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
HG/T 2048.1 Glass-lined stuffing boxes
HG/T 2051.1 Glass-lined agitator-Anchor type
HG/T 2051.2 Glass-lined agitator-Gate type
HG/T 2051.3 Glass-lined agitator-Retreat curve impeller type
HG/T 2051.4 Glass-lined agitator-Pitch blade turbine type
HG/T 2057 Mechanical seals for glass-lined vessel
HG/T 21563 System combination, selection and technical requirements of agitator drive
HG/T 21569.1 Agitator drive-coupling with short section
HG/T 21569.2 Agitator drive-block type elastic coupling
HG/T 21570 Agitator drive-coupling
JB/T 2982 Cycloidal-pin-annulus reducer
JB/T 7000-2010 Coaxial cylindrical gear reducer
JB/T 8853-2015 Bevel cylindrical gear units
3 Type, Basic Parameters and Main dimensions
3.1 Drive type see Figure 1, basic parameters and main dimensions see Table 1.
3.2 There are TB, DZ, DJ, SZ and SJ structure types according to the structure of reducer stool output shaft and supporting type (see Table 2). The TB type reducer stool output shaft has an outer-cone connection. The DZ and DJ drive shafts have single support. The SZ and SJ drive shafts have double support.
3.3 Selection of drive motor power and reducer see Annex A.
4 Reducer stool type, Basic parameters and Dimensions
4.1 TB reducer stool structure see Figure 2, basic parameters and dimensions see Table 3 and Table
4.2 DZ and DJ reducer stool structures see Figure 3, basic parameters and dimensions see Table 5,Table 6 and Table 7.
4.3 SZ and SJ reducer stool structures see Figure 4, basic parameters and dimensions see Table 8,Table 9 and Table 1
5 Markings and Examples
Example 1:
Comply to HG/T 2052, when drive unit with TB reducer stool, dN=80mm agitator shaft, N=4kW
YBX3 motor, and n=80r/min turning speed. Take as example, it marks as:
Drive for glass-lined vessel with agitator HG/T 2052–TB4(80)–YB4/80.
The meaning of each factor in the marking is as follows:
Drive for glass-lined vessel with agitator
1 Scope
This standard specifies the type, basic parameters and main dimensions, requirements, markings and examples, assembly, labels, packing, transportation and storage of drive for glass-lined vessel with agitator.
This standard is applicable to drive for glass-lined vessel with agitator.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
HG/T 2048.1 Glass-lined stuffing boxes
HG/T 2051.1 Glass-lined agitator-Anchor type
HG/T 2051.2 Glass-lined agitator-Gate type
HG/T 2051.3 Glass-lined agitator-Retreat curve impeller type
HG/T 2051.4 Glass-lined agitator-Pitch blade turbine type
HG/T 2057 Mechanical seals for glass-lined vessel
HG/T 21563 System combination, selection and technical requirements of agitator drive
HG/T 21569.1 Agitator drive-coupling with short section
HG/T 21569.2 Agitator drive-block type elastic coupling
HG/T 21570 Agitator drive-coupling
JB/T 2982 Cycloidal-pin-annulus reducer
JB/T 7000-2010 Coaxial cylindrical gear reducer
JB/T 8853-2015 Bevel cylindrical gear units
3 Type, Basic Parameters and Main dimensions
3.1 Drive type see Figure 1, basic parameters and main dimensions see Table 1.
3.2 There are TB, DZ, DJ, SZ and SJ structure types according to the structure of reducer stool output shaft and supporting type (see Table 2). The TB type reducer stool output shaft has an outer-cone connection. The DZ and DJ drive shafts have single support. The SZ and SJ drive shafts have double support.
3.3 Selection of drive motor power and reducer see Annex A.
4 Reducer stool type, Basic parameters and Dimensions
4.1 TB reducer stool structure see Figure 2, basic parameters and dimensions see Table 3 and Table
4.2 DZ and DJ reducer stool structures see Figure 3, basic parameters and dimensions see Table 5,Table 6 and Table 7.
4.3 SZ and SJ reducer stool structures see Figure 4, basic parameters and dimensions see Table 8,Table 9 and Table 1
5 Markings and Examples
Example 1:
Comply to HG/T 2052, when drive unit with TB reducer stool, dN=80mm agitator shaft, N=4kW
YBX3 motor, and n=80r/min turning speed. Take as example, it marks as:
Drive for glass-lined vessel with agitator HG/T 2052–TB4(80)–YB4/80.
The meaning of each factor in the marking is as follows:
TB4(80) ——reducer stool item number TB4, agitator shaft nominal diameter 80mm;
YB4/80 ——Type-YB motor, 4kW motor power, 80r/min agitator turning speed.
Example 2
