1 Scope
This standard specifies the designation, boundary dimensions and technical specifications of double-row angular contact ball bearings for electromagnetic clutch of car air-conditioner (hereinafter referred to as "bearings").
This standard is applicable to the production inspection and customer acceptance of bearings.
2 Normative References
The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding corrections to) or revisions of, any of these publications do not apply. However, all parties coming to an agreement basing on this standard are encouraged to investigate whether the latest editions are applicable. For undated normative references, the latest editions apply.
GB/T 272-1993 "Rolling Bearing - Identification Code"
GB/T 307.2-2005 "Rolling Bearings - Measuring and Gauging Principles and Methods" (ISO 1132-2: 2001, Rolling Bearings - Tolerances - Part 2: Measuring and Gauging Principles and Methods, MOD)
GB/T 307.3-2005 "Rolling Bearings - General Technical Regulations"
GB/T 2829-2002 "Sampling Procedures and Tables for Periodic Inspection by Attributes (Apply to Inspection of Process Stability)"
GB/T 4199-2003 "Rolling Bearings - Tolerances - Definitions" (ISO 1132-1: 2000, Rolling Bearings - Tolerances - Part 1: Terms and Definitions, MOD)
GB/T 7811-1999 "Rolling Bearings - Symbols for Quantities"
GB/T 8597-2003 "Rolling Bearings - Rust Proof Packaging"
GB/T 18254-2002 "High-carbon Chromium Bearing Steel Technical Specifications"
JB/T 1255-2001 "Specification for Heat-treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel"
JB/T 2974-2004 "Rolling Bearings - Identification Code - Supplemental Regulations"
JB/T 3573-2004 "Rolling Bearings - Methods for the Measurement of Radial Internal Clearance"
JB/T3574-1997 "Rolling Bearings - Marking for Products"
JB/T 5314-2002 "Rolling bearing - Measuring Methods for Vibration (Acceleration)"
JB/T 6641-1993 "Rolling Bearings - Residual Magnetism and Its Assessment Method"
JB/T 7050-2005 "Rolling Bearings - Assessment Methods for Cleanliness"
JB/T 7051-1993 "Rolling Bearing - Methods for the Measurement and Assessment of Parts Surface Roughness"
JB/T 7752-2005 "Sealed Deep Groove Ball Bearings - Specifications"
JB/T 8571-1997 "Rolling Bearings - Sealed Deep Groove Ball Bearings - Performance Test Rule of Dustproofing, Grease Leakage and Temperature Rise"
JB/T 8921-1999 "Rolling Bearings and Commercial Parts-Inspection Rules"
3 Symbols
For the purposes of this standard, the symbols established in GB/T 4199 and GB/T 7811 apply(see Figure 1).
4 Designation Method
The bearing designation consists of the type code, the dimensions indicating the characteristics of bearing matching and mounting, and the suffix code, arranged in the order specified in Table 1.
Contents
Foreword I
1 Scope
2 Normative References
3 Symbols
4 Designation Method
4.1 Type Code
4.2 Dimension Code
4.3 Suffix Code
4.4 Example
5 Boundary Dimensions
6 Technical Requirements
6.1 Materials and Heat Treatment
6.2 Tolerance
6.3 Surface Roughness
6.4 Contact Angle
6.5 Clearance
6.6 Residual Magnetism
6.7 Cleanliness
6.8 Vibration
6.9 Rotating Flexibility
6.10 Lubrication and Sealing
6.11 Appearance Quality
6.12 High Temperature, High Speed, and Durability
6.13 Others
7 Test Methods
8 Inspection Rules
8.1 Delivery Inspection
8.2 Type Inspection
9 Symbols
10 Packaging
Appendix A (Informative) Boundary Dimensions of Other Bearings
1 Scope
This standard specifies the designation, boundary dimensions and technical specifications of double-row angular contact ball bearings for electromagnetic clutch of car air-conditioner (hereinafter referred to as "bearings").
This standard is applicable to the production inspection and customer acceptance of bearings.
2 Normative References
The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding corrections to) or revisions of, any of these publications do not apply. However, all parties coming to an agreement basing on this standard are encouraged to investigate whether the latest editions are applicable. For undated normative references, the latest editions apply.
GB/T 272-1993 "Rolling Bearing - Identification Code"
GB/T 307.2-2005 "Rolling Bearings - Measuring and Gauging Principles and Methods" (ISO 1132-2: 2001, Rolling Bearings - Tolerances - Part 2: Measuring and Gauging Principles and Methods, MOD)
GB/T 307.3-2005 "Rolling Bearings - General Technical Regulations"
GB/T 2829-2002 "Sampling Procedures and Tables for Periodic Inspection by Attributes (Apply to Inspection of Process Stability)"
GB/T 4199-2003 "Rolling Bearings - Tolerances - Definitions" (ISO 1132-1: 2000, Rolling Bearings - Tolerances - Part 1: Terms and Definitions, MOD)
GB/T 7811-1999 "Rolling Bearings - Symbols for Quantities"
GB/T 8597-2003 "Rolling Bearings - Rust Proof Packaging"
GB/T 18254-2002 "High-carbon Chromium Bearing Steel Technical Specifications"
JB/T 1255-2001 "Specification for Heat-treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel"
JB/T 2974-2004 "Rolling Bearings - Identification Code - Supplemental Regulations"
JB/T 3573-2004 "Rolling Bearings - Methods for the Measurement of Radial Internal Clearance"
JB/T3574-1997 "Rolling Bearings - Marking for Products"
JB/T 5314-2002 "Rolling bearing - Measuring Methods for Vibration (Acceleration)"
JB/T 6641-1993 "Rolling Bearings - Residual Magnetism and Its Assessment Method"
JB/T 7050-2005 "Rolling Bearings - Assessment Methods for Cleanliness"
JB/T 7051-1993 "Rolling Bearing - Methods for the Measurement and Assessment of Parts Surface Roughness"
JB/T 7752-2005 "Sealed Deep Groove Ball Bearings - Specifications"
JB/T 8571-1997 "Rolling Bearings - Sealed Deep Groove Ball Bearings - Performance Test Rule of Dustproofing, Grease Leakage and Temperature Rise"
JB/T 8921-1999 "Rolling Bearings and Commercial Parts-Inspection Rules"
3 Symbols
For the purposes of this standard, the symbols established in GB/T 4199 and GB/T 7811 apply(see Figure 1).
4 Designation Method
The bearing designation consists of the type code, the dimensions indicating the characteristics of bearing matching and mounting, and the suffix code, arranged in the order specified in Table 1.
Contents of JB/T 10531-2005
Contents
Foreword I
1 Scope
2 Normative References
3 Symbols
4 Designation Method
4.1 Type Code
4.2 Dimension Code
4.3 Suffix Code
4.4 Example
5 Boundary Dimensions
6 Technical Requirements
6.1 Materials and Heat Treatment
6.2 Tolerance
6.3 Surface Roughness
6.4 Contact Angle
6.5 Clearance
6.6 Residual Magnetism
6.7 Cleanliness
6.8 Vibration
6.9 Rotating Flexibility
6.10 Lubrication and Sealing
6.11 Appearance Quality
6.12 High Temperature, High Speed, and Durability
6.13 Others
7 Test Methods
8 Inspection Rules
8.1 Delivery Inspection
8.2 Type Inspection
9 Symbols
10 Packaging
Appendix A (Informative) Boundary Dimensions of Other Bearings
