1 Scope
This standard specifies the testing methods for CDMA digital cellular mobile communication network ME-UIM Card Interface, including testing methods and judgment criteria for electricity, protocol, security and application, etc. It does not include the content of the UIM-ME application toolbox.
It is applicable to terminal equipment using user identify module (UIM) in CDMA digital cellular mobile communication network.
2 Normative References
The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding the correction contents), or revisions do not applicable to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of these references indicated below. For undated references, the latest editions apply.
YD/T 1168-2007 Technical Specification for CDMA Digital Cellular Mobile Communication Network User Identify Module (UIM)
3 Abbreviations
For the purposes of this document, the following abbreviations apply.
ACM Associative Communication Multiplexer
AND Abbreviated Dialing Number
ATR Answer To Reset
BCD Binary Coded Decimal
CAVE Celluar Authenticated and Encrypt
CDMA Code Division Multiple Access
CLK CLocK
CPN Calling Party Number
CHV Card Holder Verification
DF Directory File
etu Elementary time unit
ESN External Subscriber Number
FDN Fixed Dialing Number
FT Fixed Termination
GND Ground
ID IDentifier
IEC International Electrotechnical Commission
IMEI International Mobile Equipment Identity
INS INStruction
ISO International Organization for Standardization
I/O Input/Output
IUT Implementation Under Test
LSB Least Significant Bit
MCC Mobile Country Code
MSB Most Significant Bit
ME Mobile Equipment
MS Mobile Station
MSID Mobile Station ID
MSIN Mobile Station Identity Number
MMI Man Machine Interface
NPI Numbering Plan Identifier
OTASP/OTAPA Over the Air Service Provisioning/Over the Air Parameter Administration
PIN Personal Identity Number
PIN2 Personal Identity Number 2
PPS Protocol and Parameter Selection
PRL Preferred Roaming List
PUK PIN Unblocking Key
PUK2 PIN2 Unblocking Key
RST ReSet
R-UIM Removable User Identify Module
SPASM Subscriber Parameter Administration Security Mechanism
State A Space or Low State
State H High State Logic Level
State L Low State Logic Level
State Z Mark or High Level
SS System Simulator
SID/NID System Identity/Network Identity
SSD Shared Secret Data
SW Status Word
TON Type Of Number
UI User Interface
UIM User Identity Module
4 Test Conditions
4.1 General
The test on the ME will confirm the following in sequence:
1) ME is able to correctly read the data in the R-UIM
2) ME is able to correctly write the data to the R-UIM;
3) ME is able to properly originate appropriate procedures;
4) the underlying protocol;
5) electrical feature;
6) physical feature.
All tests are applicable to the ME which meets requirements of Technical Specification for CDMA Digital Cellular Mobile Communication Network User Identify Module (UIM), and uses Type ID-1 or Type Plug-in R-UIM.
The R-UIM simulator will be a part of the System Simulator (SS). In order to perform a logic feature test, special data needs to be programmed into the R-UIM. If the data in the R-UIM differs from the defaults defined below, the required data will be declared in the initial test condition.
4.1.1 EFCST (CDMA Service List)
Unless otherwise defined, the CDMA service list shall be numbered in accordance with "EFCST Setting 1” of Table 1.
Foreword i
1 Scope
2 Normative References
3 Abbreviations
4 Test Conditions
5 ME Test Procedure
Annex A (Normative) Functional Requirements of the R-UIM Simulator
1 Scope
This standard specifies the testing methods for CDMA digital cellular mobile communication network ME-UIM Card Interface, including testing methods and judgment criteria for electricity, protocol, security and application, etc. It does not include the content of the UIM-ME application toolbox.
It is applicable to terminal equipment using user identify module (UIM) in CDMA digital cellular mobile communication network.
2 Normative References
The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding the correction contents), or revisions do not applicable to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of these references indicated below. For undated references, the latest editions apply.
YD/T 1168-2007 Technical Specification for CDMA Digital Cellular Mobile Communication Network User Identify Module (UIM)
3 Abbreviations
For the purposes of this document, the following abbreviations apply.
ACM Associative Communication Multiplexer
AND Abbreviated Dialing Number
ATR Answer To Reset
BCD Binary Coded Decimal
CAVE Celluar Authenticated and Encrypt
CDMA Code Division Multiple Access
CLK CLocK
CPN Calling Party Number
CHV Card Holder Verification
DF Directory File
etu Elementary time unit
ESN External Subscriber Number
FDN Fixed Dialing Number
FT Fixed Termination
GND Ground
ID IDentifier
IEC International Electrotechnical Commission
IMEI International Mobile Equipment Identity
INS INStruction
ISO International Organization for Standardization
I/O Input/Output
IUT Implementation Under Test
LSB Least Significant Bit
MCC Mobile Country Code
MSB Most Significant Bit
ME Mobile Equipment
MS Mobile Station
MSID Mobile Station ID
MSIN Mobile Station Identity Number
MMI Man Machine Interface
NPI Numbering Plan Identifier
OTASP/OTAPA Over the Air Service Provisioning/Over the Air Parameter Administration
PIN Personal Identity Number
PIN2 Personal Identity Number 2
PPS Protocol and Parameter Selection
PRL Preferred Roaming List
PUK PIN Unblocking Key
PUK2 PIN2 Unblocking Key
RST ReSet
R-UIM Removable User Identify Module
SPASM Subscriber Parameter Administration Security Mechanism
State A Space or Low State
State H High State Logic Level
State L Low State Logic Level
State Z Mark or High Level
SS System Simulator
SID/NID System Identity/Network Identity
SSD Shared Secret Data
SW Status Word
TON Type Of Number
UI User Interface
UIM User Identity Module
4 Test Conditions
4.1 General
The test on the ME will confirm the following in sequence:
1) ME is able to correctly read the data in the R-UIM
2) ME is able to correctly write the data to the R-UIM;
3) ME is able to properly originate appropriate procedures;
4) the underlying protocol;
5) electrical feature;
6) physical feature.
All tests are applicable to the ME which meets requirements of Technical Specification for CDMA Digital Cellular Mobile Communication Network User Identify Module (UIM), and uses Type ID-1 or Type Plug-in R-UIM.
The R-UIM simulator will be a part of the System Simulator (SS). In order to perform a logic feature test, special data needs to be programmed into the R-UIM. If the data in the R-UIM differs from the defaults defined below, the required data will be declared in the initial test condition.
4.1.1 EFCST (CDMA Service List)
Unless otherwise defined, the CDMA service list shall be numbered in accordance with "EFCST Setting 1” of Table 1.
Contents of YD/T 1683-2007
Foreword i
1 Scope
2 Normative References
3 Abbreviations
4 Test Conditions
5 ME Test Procedure
Annex A (Normative) Functional Requirements of the R-UIM Simulator
