1 General provisions
1.0.1 This specification is the technical basis for construction quality inspection, on-site inspection and completion acceptance of indoor coverage system installation engineering for wireless communication, and is applicable to newly built indoor coverage system installation engineering for wireless communication. Expansion and reconstruction engineering shall be implemented with reference.
1.0.2 This specification is mainly prepared according to YD/T 5120-2005 Specification on indoor coverage engineering design for wireless communication system and other technical documents.
1.0.3 This specification refers to the acceptance of installation engineering of signal source part and indoor antenna and feeder distribution system part of indoor coverage system installation engineering for wireless communication, and the acceptance of other works on the network side shall refer to corresponding standards and specifications.
1.0.4 The equipment acceptance of base station equipment and repeater equipment involved in the indoor coverage system installation engineering for wireless communication may be carried out according to the requirements of relevant technical system and engineering technical specifications.
1.0.5 In the process of engineering acceptance, the developing unit shall organize relevant units to be present at the same time, and conduct acceptance in strict accordance with this specification.
1.0.6 In addition to the requirements stipulated in this specification, the acceptance of the indoor coverage system installation engineering for wireless communication shall comply with the current relevant engineering construction standards of the nation. In case of any conflict between this specification and self-developing procedures developed by the developing unit and construction unit, this specification shall prevail.
1.0.7 The equipment and devices selected in the engineering shall provided with the telecommunication equipment network access license and seismic performance test certificate issued by the Ministry of Information Industry.
1.0.8 In case of special circumstances, when there are difficulties in implementing this specification, adequate reasons shall be provided, and a report shall be provided to the higher authorities for approval.
1.0.9 The acceptance of indoor coverage system installation engineering for wireless communication shall be carried out in accordance with the requirements of Figure 1.0.9.
Foreword i
1 General provisions
2 System composition
3 Inspection before engineering acceptance
3.1 Installation environment inspection
3.2 Equipment and apparatus inspection before installation
3.3 Cable tray installation (or channels)
3.4 Installation of signal source equipment
3.5 Cable layout
3.6 Installation of active devices
3.7 Installation of passive devices
3.8 Antenna installation
3.9 Power up inspection
4 Preliminary acceptance of engineering
4.1 Test requirements
4.2 Inspection and test of signal source equipment
4.3 Inspection and test of indoor coverage system
4.4 Inspection and test of indoor coverage system
4.5 Handover of technical document and breakup
5 Engineering commissioning
5.1 Acceptance requirements for commissioning
5.2 Commissioning observation indicators
6 Final inspection of the engineering
6.1 Technical documents of engineering completion
6.2 Acceptance requirements and content
Annex A Explanation of wording in this specification
Annex B List of inspection items for engineering completion
Standard
YD/T 5160-2007 Acceptance Specifications on Indoor Coverage System Installation Engineering for Wireless Communication (English Version)
Standard No.
YD/T 5160-2007
Status
superseded
Language
English
File Format
PDF
Word Count
8500 words
Price(USD)
400.0
Implemented on
2007-12-1
Delivery
via email in 1 business day
Detail of YD/T 5160-2007
Standard No.
YD/T 5160-2007
English Name
Acceptance Specifications on Indoor Coverage System Installation Engineering for Wireless Communication
1 General provisions
1.0.1 This specification is the technical basis for construction quality inspection, on-site inspection and completion acceptance of indoor coverage system installation engineering for wireless communication, and is applicable to newly built indoor coverage system installation engineering for wireless communication. Expansion and reconstruction engineering shall be implemented with reference.
1.0.2 This specification is mainly prepared according to YD/T 5120-2005 Specification on indoor coverage engineering design for wireless communication system and other technical documents.
1.0.3 This specification refers to the acceptance of installation engineering of signal source part and indoor antenna and feeder distribution system part of indoor coverage system installation engineering for wireless communication, and the acceptance of other works on the network side shall refer to corresponding standards and specifications.
1.0.4 The equipment acceptance of base station equipment and repeater equipment involved in the indoor coverage system installation engineering for wireless communication may be carried out according to the requirements of relevant technical system and engineering technical specifications.
1.0.5 In the process of engineering acceptance, the developing unit shall organize relevant units to be present at the same time, and conduct acceptance in strict accordance with this specification.
1.0.6 In addition to the requirements stipulated in this specification, the acceptance of the indoor coverage system installation engineering for wireless communication shall comply with the current relevant engineering construction standards of the nation. In case of any conflict between this specification and self-developing procedures developed by the developing unit and construction unit, this specification shall prevail.
1.0.7 The equipment and devices selected in the engineering shall provided with the telecommunication equipment network access license and seismic performance test certificate issued by the Ministry of Information Industry.
1.0.8 In case of special circumstances, when there are difficulties in implementing this specification, adequate reasons shall be provided, and a report shall be provided to the higher authorities for approval.
1.0.9 The acceptance of indoor coverage system installation engineering for wireless communication shall be carried out in accordance with the requirements of Figure 1.0.9.
Contents of YD/T 5160-2007
Foreword i
1 General provisions
2 System composition
3 Inspection before engineering acceptance
3.1 Installation environment inspection
3.2 Equipment and apparatus inspection before installation
3.3 Cable tray installation (or channels)
3.4 Installation of signal source equipment
3.5 Cable layout
3.6 Installation of active devices
3.7 Installation of passive devices
3.8 Antenna installation
3.9 Power up inspection
4 Preliminary acceptance of engineering
4.1 Test requirements
4.2 Inspection and test of signal source equipment
4.3 Inspection and test of indoor coverage system
4.4 Inspection and test of indoor coverage system
4.5 Handover of technical document and breakup
5 Engineering commissioning
5.1 Acceptance requirements for commissioning
5.2 Commissioning observation indicators
6 Final inspection of the engineering
6.1 Technical documents of engineering completion
6.2 Acceptance requirements and content
Annex A Explanation of wording in this specification
Annex B List of inspection items for engineering completion
