GB 36672-2026 Safety requirements of lithium-ion battery for electric motorcycles and electric mopeds
1 Scope
This document specifies the safety requirements of lithium‑ion battery cells, battery packs or battery systems for electric motorcycles and electric mopeds, and describes the corresponding test methods.
This document is applicable to lithium-ion battery for electric motorcycles and electric mopeds.
2 Normative references
The contents in the following documents constitute essential provisions of this document through normative references in the text. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.4-2008 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12h+12h cycle)
GB/T 2423.18-2021 Environmental testing - Part 2: Test methods - Test Kb: Salt mist, cyclic (sodium chloride solution)
GB/T 2423.43 Environmental testing for electric and electronic products - Part 2: Test methods - Mounting of specimens for vibration impact and similar dynamic tests
GB/T 5169.5-2020 Fire hazard testing for electric and electronic products - Part 5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
GB/T 5169.16 Fire hazard testing for electric and electronic products - Part 16: Test flames - 50 W horizontal and vertical flame test methods
GB/T 5359.1 Term for motorcycles and mopeds - Part 1: Types of vehicles
GB 18384 Electric vehicles safety requirements
GB/T 19596 Terminology of electric vehicles
GB/T 19951-2026 Road vehicles - Test methods for electrical disturbances from electrostatic discharge
GB/T 34013 Dimension of traction battery for electric vehicles
GB/T 34014 Coding regulation for automotive traction battery
GB 42296 Safety technical requirements of charger for electric bicycles
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 5359.1 and GB/T 19596 and the following apply.
3.1
battery cell
basic unit device that converts chemical energy and electric energy to each other
NOTE It generally consists of electrodes, diaphragms, electrolyte, case and terminals, and is designed to be rechargeable.
[SOURCE: GB/T 38031-2025, 3.1]
3.2
battery module
combination in which more than one battery cell is connected in series, in parallel, or in series‑parallel and used as a power source
[SOURCE: GB 38031-2025, 3.2]
3.3
battery pack
unit that obtains electrical energy from an external source and can output electrical energy externally
NOTE It usually includes battery cells, battery signal acquisition units, battery boxes and corresponding accessories (cooling components, connecting cables, etc.).
[SOURCE: GB 38031‑2025, 3.3, modified]
3.4
battery system
energy storage device consisting of one or more battery packs and corresponding accessories (management system, high‑voltage circuit, low‑voltage circuit and mechanical assembly, etc.)
[SOURCE: GB 38031-2025, 3.4]
3.5
rated capacity
capacity value of a battery cell, battery pack or battery system measured under the conditions specified by the manufacturer and declared by the manufacturer
NOTE Rated capacity is usually expressed in ampere‑hours (Ah) or milliampere‑hours (mAh).
[SOURCE: GB 38031‑2025, 3.8, modified]
3.6
practical capacity
capacity value released from a fully charged battery cell, battery pack or battery system under the conditions specified by the manufacturer
[SOURCE: GB 38031‑2025, 3.9, modified]
3.7
state-of-charge; SOC
percentage of the capacity released from the current battery cell, battery pack or battery system under the discharge conditions specified by the manufacturer to the practical capacity
[SOURCE: GB 38031‑2025, 3.10, modified]
3.8
end-of-charge voltage
Uce
maximum voltage permitted to be reached when a battery cell, battery pack or battery system is charged under the conditions specified by the manufacturer
[SOURCE: GB 38031‑2025, 3.18, modified]
3.9
end-of-discharge voltage
Ude
minimum voltage permitted to be reached when a battery cell, battery pack or battery system is discharged under the conditions specified by the manufacturer
[SOURCE: GB 38031‑2025, 3.19, modified]
3.10
protected charging voltage
Ucp
protection circuit operating voltage specified by the manufacturer when a battery pack or battery system is charged
4 Symbols and abbreviated terms
4.1 Symbols
For the purposes of this document, the following symbols apply.
I₃: 3 h rate discharge current (A), whose value is equal to 1/3 of the rated capacity value.
4.2 Abbreviated terms
For the purposes of this standard, the following abbreviated terms apply.
FS: Full Scale
PSD: Power Spectral Density
RMS: Root Mean Square
5 Safety requirements
5.1 Common requirements
Echelon‑use lithium‑ion batteries shall not be used in electric motorcycles and electric mopeds.
The safety design of lithium‑ion batteries for electric motorcycles and electric mopeds shall take into account their intended use and reasonably foreseeable misuse conditions. To ensure the safe use of lithium‑ion batteries under different conditions, their safe operating conditions shall be specified, including parameters such as voltage range, current range and temperature range. The manufacturer shall indicate at least the information in Table 1 in the product technical documentation.
Table 1 - Information to be indicated at least in the battery product technical documentation
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Safety requirements
6 Test conditions
7 Test preparation
8 Test methods
9 Determination of the same type
10 Type test
11 Implementation of the standard
Annex A (Normative) Flame retardance test method for wires
Bibliography
GB 36672-2026 Safety requirements of lithium-ion battery for electric motorcycles and electric mopeds
1 Scope
This document specifies the safety requirements of lithium‑ion battery cells, battery packs or battery systems for electric motorcycles and electric mopeds, and describes the corresponding test methods.
This document is applicable to lithium-ion battery for electric motorcycles and electric mopeds.
2 Normative references
The contents in the following documents constitute essential provisions of this document through normative references in the text. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.4-2008 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12h+12h cycle)
GB/T 2423.18-2021 Environmental testing - Part 2: Test methods - Test Kb: Salt mist, cyclic (sodium chloride solution)
GB/T 2423.43 Environmental testing for electric and electronic products - Part 2: Test methods - Mounting of specimens for vibration impact and similar dynamic tests
GB/T 5169.5-2020 Fire hazard testing for electric and electronic products - Part 5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
GB/T 5169.16 Fire hazard testing for electric and electronic products - Part 16: Test flames - 50 W horizontal and vertical flame test methods
GB/T 5359.1 Term for motorcycles and mopeds - Part 1: Types of vehicles
GB 18384 Electric vehicles safety requirements
GB/T 19596 Terminology of electric vehicles
GB/T 19951-2026 Road vehicles - Test methods for electrical disturbances from electrostatic discharge
GB/T 34013 Dimension of traction battery for electric vehicles
GB/T 34014 Coding regulation for automotive traction battery
GB 42296 Safety technical requirements of charger for electric bicycles
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 5359.1 and GB/T 19596 and the following apply.
3.1
battery cell
basic unit device that converts chemical energy and electric energy to each other
NOTE It generally consists of electrodes, diaphragms, electrolyte, case and terminals, and is designed to be rechargeable.
[SOURCE: GB/T 38031-2025, 3.1]
3.2
battery module
combination in which more than one battery cell is connected in series, in parallel, or in series‑parallel and used as a power source
[SOURCE: GB 38031-2025, 3.2]
3.3
battery pack
unit that obtains electrical energy from an external source and can output electrical energy externally
NOTE It usually includes battery cells, battery signal acquisition units, battery boxes and corresponding accessories (cooling components, connecting cables, etc.).
[SOURCE: GB 38031‑2025, 3.3, modified]
3.4
battery system
energy storage device consisting of one or more battery packs and corresponding accessories (management system, high‑voltage circuit, low‑voltage circuit and mechanical assembly, etc.)
[SOURCE: GB 38031-2025, 3.4]
3.5
rated capacity
capacity value of a battery cell, battery pack or battery system measured under the conditions specified by the manufacturer and declared by the manufacturer
NOTE Rated capacity is usually expressed in ampere‑hours (Ah) or milliampere‑hours (mAh).
[SOURCE: GB 38031‑2025, 3.8, modified]
3.6
practical capacity
capacity value released from a fully charged battery cell, battery pack or battery system under the conditions specified by the manufacturer
[SOURCE: GB 38031‑2025, 3.9, modified]
3.7
state-of-charge; SOC
percentage of the capacity released from the current battery cell, battery pack or battery system under the discharge conditions specified by the manufacturer to the practical capacity
[SOURCE: GB 38031‑2025, 3.10, modified]
3.8
end-of-charge voltage
Uce
maximum voltage permitted to be reached when a battery cell, battery pack or battery system is charged under the conditions specified by the manufacturer
[SOURCE: GB 38031‑2025, 3.18, modified]
3.9
end-of-discharge voltage
Ude
minimum voltage permitted to be reached when a battery cell, battery pack or battery system is discharged under the conditions specified by the manufacturer
[SOURCE: GB 38031‑2025, 3.19, modified]
3.10
protected charging voltage
Ucp
protection circuit operating voltage specified by the manufacturer when a battery pack or battery system is charged
4 Symbols and abbreviated terms
4.1 Symbols
For the purposes of this document, the following symbols apply.
I₃: 3 h rate discharge current (A), whose value is equal to 1/3 of the rated capacity value.
4.2 Abbreviated terms
For the purposes of this standard, the following abbreviated terms apply.
FS: Full Scale
PSD: Power Spectral Density
RMS: Root Mean Square
5 Safety requirements
5.1 Common requirements
Echelon‑use lithium‑ion batteries shall not be used in electric motorcycles and electric mopeds.
The safety design of lithium‑ion batteries for electric motorcycles and electric mopeds shall take into account their intended use and reasonably foreseeable misuse conditions. To ensure the safe use of lithium‑ion batteries under different conditions, their safe operating conditions shall be specified, including parameters such as voltage range, current range and temperature range. The manufacturer shall indicate at least the information in Table 1 in the product technical documentation.
Table 1 - Information to be indicated at least in the battery product technical documentation
Contents of GB 36672-2026
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Safety requirements
6 Test conditions
7 Test preparation
8 Test methods
9 Determination of the same type
10 Type test
11 Implementation of the standard
Annex A (Normative) Flame retardance test method for wires
Bibliography