1 Scope
This Standard specifies the terms and definitions of inspection and test, examination, inspection and supplementary inspection, pressure test, test results, pressure test method, certificate of qualification and retest of valve for petroleum, petrifying and relevant industry.
This Standard is applicable to inspection and pressure test of gate valve, stop valve, plug valve, ball valve, back pressure valve and butterfly valve of metal sealing pair made up of metal and metal, resilient seal made up of metal and non-metal elastic materials, and non-metal sealing pair made up of non-metal and non-metallic materials.
This Standard may also be applicable to other types of valves upon the consent of the Supplier and the Purchaser.
The inspection items of this Standard include:
- Appearance inspection of caster;
- Shell test;
- Upper seal test
- Low-pressure seal test;
- High-pressure seal test;
- Double block and bleed sealing test;
- High pressure gas shell test.
2 Normative References
The following referenced documents are indispensable for the application of this Document. For dated references, only the dated versions apply to this Standard. For undated references, the latest edition of the normative document (include all the amendments) is applicable to this Document.
GB/T 12224 General Requirements for Industrial Steel Valves (GB/T 12224-2005, ASTM B16.34a:1998, NEQ)
JB/T 7927 Valve Cast Steel Visual Quality Requirements
3 Terms
For the purpose of this Document, the following terms and definitions apply.
3.1 Resilient Seal
It refers to the sealing pair (for example, oil seal plug valve) made up of soft sealing pair, solid and semi-solid consistent grease, and sealing pair made up of soft seal and metallic seal.
Foreword I
1 Scope
2 Normative References
3 Terms
4 Examination, Inspection and Supplementary Inspection
4.1 Examination within the Plant of Valve Manufacturer
4.2 Examinatin outside the Plant of Valve Manufacturer
4.3 Examination Notification
4.4 Examination Scope
4.5 Inspection
5 Pressure Test
5.1 Test Site
5.2 Test Equipment
5.3 Test Requirement
5.4 Test Pressure
5.5 Test Duration
6 Test Result
6.1 Shell Test, Stem Sealing and Upper Seal Test
6.2 Seal Test
7 Pressure Test Method
7.1 General Requirements
7.2 Shell Test
7.3 Upper Seal Test
7.4 Low-pressure Seal Test
7.5 High-pressure Seal Test
7.6 High Pressure Test for Double Block and Bleed Valve
8 Certificate of Conformity and Retest of the Valve
8.1 Conformity Certificate
8.2 Retest
Appendix A (Informative) Comparison Table on the Chapter and Article Number of this Standard and API 598:
Appendix B (Informative) Technical Differences between this Standard and API 598 : 2009 and their Reasons
1 Scope
This Standard specifies the terms and definitions of inspection and test, examination, inspection and supplementary inspection, pressure test, test results, pressure test method, certificate of qualification and retest of valve for petroleum, petrifying and relevant industry.
This Standard is applicable to inspection and pressure test of gate valve, stop valve, plug valve, ball valve, back pressure valve and butterfly valve of metal sealing pair made up of metal and metal, resilient seal made up of metal and non-metal elastic materials, and non-metal sealing pair made up of non-metal and non-metallic materials.
This Standard may also be applicable to other types of valves upon the consent of the Supplier and the Purchaser.
The inspection items of this Standard include:
- Appearance inspection of caster;
- Shell test;
- Upper seal test
- Low-pressure seal test;
- High-pressure seal test;
- Double block and bleed sealing test;
- High pressure gas shell test.
2 Normative References
The following referenced documents are indispensable for the application of this Document. For dated references, only the dated versions apply to this Standard. For undated references, the latest edition of the normative document (include all the amendments) is applicable to this Document.
GB/T 12224 General Requirements for Industrial Steel Valves (GB/T 12224-2005, ASTM B16.34a:1998, NEQ)
JB/T 7927 Valve Cast Steel Visual Quality Requirements
3 Terms
For the purpose of this Document, the following terms and definitions apply.
3.1 Resilient Seal
It refers to the sealing pair (for example, oil seal plug valve) made up of soft sealing pair, solid and semi-solid consistent grease, and sealing pair made up of soft seal and metallic seal.
Contents of GB/T 26480-2011
Foreword I
1 Scope
2 Normative References
3 Terms
4 Examination, Inspection and Supplementary Inspection
4.1 Examination within the Plant of Valve Manufacturer
4.2 Examinatin outside the Plant of Valve Manufacturer
4.3 Examination Notification
4.4 Examination Scope
4.5 Inspection
5 Pressure Test
5.1 Test Site
5.2 Test Equipment
5.3 Test Requirement
5.4 Test Pressure
5.5 Test Duration
6 Test Result
6.1 Shell Test, Stem Sealing and Upper Seal Test
6.2 Seal Test
7 Pressure Test Method
7.1 General Requirements
7.2 Shell Test
7.3 Upper Seal Test
7.4 Low-pressure Seal Test
7.5 High-pressure Seal Test
7.6 High Pressure Test for Double Block and Bleed Valve
8 Certificate of Conformity and Retest of the Valve
8.1 Conformity Certificate
8.2 Retest
Appendix A (Informative) Comparison Table on the Chapter and Article Number of this Standard and API 598:
Appendix B (Informative) Technical Differences between this Standard and API 598 : 2009 and their Reasons
