Amendment 1
of
TSG ZF003-2011 Safety Technical Supervision Regulations for Bursting Disc Devices
I Amendment to the “text”
1 Article 3 is amended to:
“This Regulation specifies the basic safety requirements for the process of material, design, manufacture, inspection, installation, application and others as well as for the manufacture licensing, type test work of bursting disc devices. The technical standards of the relevant bursting disc device and the management systems of the relevant organizations and institutions shall not be less stringent than requirements of this Regulation.
The safety technical requirements for bursting disc devices are detailed in Appendix B.”
2 Article 4 is amended to:
“The manufacturing organization of bursting disc devices shall obtain the corresponding "Special Equipment Manufacture License” and “Type Test Certificate of Special Equipment”. The General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China (hereinafter referred to as "AQSIQ") shall be responsible for the acceptance, examination and approval of the manufacture license of domestic and overseas bursting disc devices.
The "Special Equipment Manufacture License” is valid for four years. The bursting disc device manufacturing organization shall adopt appropriate mode to mark the "TS" license sign, the serial number of "Special Equipment Manufacture License” and the license level on the product.
The manufacture license for bursting disc devices is classified into two levels: Class A and Class B. Class A bursting disc device manufacturers have no restrictions on the application of their products, while Class B bursting disc device manufacturers are limited to products used in Class I and Class II stationary pressure vessels, cylinders, cylinder valves, and GC2/GC3 pressure pipelines.
The manufacture licensing procedure of bursting disc devices shall include application, acceptance, trial production, type test, appraisal and evaluation, examination and approval, and license issuing, etc. The specific licensing procedure shall be carried out in accordance with relevant provisions. The manufacture license conditions of bursting disc devices are detailed in Appendix C.”
3 Article 8 is amended to:
“The bursting disc device manufacturing organization shall carry out the manufacture of products in accordance with the approved license scope and also shall accept the random inspection of the safety and quality of the bursting disc device by the special equipment type test organization.
Special equipment type test organizations shall reasonably arrange random inspections, and urge the manufacturing organizations of bursting disc devices to maintain consistent product safety and quality during the period of holding the license. The scope of random inspections shall cover the product forms under manufacture license within four years, and the inspection items and qualified indicators shall not be lower than those of type tests.”
II Amendment to “Appendix A”
1 The content of A5 is deleted and the original numbers of A6 to A15 are changed to A5 to A14 in sequence.
2 A7.2 is amended to:
“A6.2 Maximum (minimum) bursting pressure
Algebraic sum of specified bursting pressure plus performance tolerance.”
3 A7.4 is deleted.
.......
Article 1 This Regulation was formulated in accordance with "Regulations on Safety Supervision of Special Equipment" (hereinafter referred to as the "Regulations") for the purpose of ensuring the safety performance of the bursting disc devices of special equipments and strengthening the safety supervision work of bursting disc devices.
Article 2 This Regulation is applicable to the bursting disc devices used for those special equipments specified in the "Regulations".
The bursting disc device is composed of such spare parts as bursting disc and bursting disc holder. The terms related to bursting disc devices involved in this Regulation are detailed in Appendix A.
Article 3 This Regulation specifies the basic safety requirements for the process of material, design, inspection, installation, application and others as well as for the manufacture licensing, type test, supervision and inspection work of bursting disc devices. The relevant provisions of the corresponding technical standards and management systems shall not be less than requirements of this Regulation.
The safety technical requirements for bursting disc devices are detailed in Appendix B.
Article 4 The manufacturing organization of bursting disc devices shall obtain the corresponding manufacture license of special equipments. The General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China (hereinafter referred to as "AQSIQ") shall be responsible for the acceptance, examination and approval of the manufacture license of domestic and overseas bursting disc devices.
The "Special Equipment Manufacture License" is valid for four years. The bursting disc device manufacturing organization holding the manufacture license shall adopt appropriate mode to mark the "TS" license sign and the serial number of "Special Equipment Manufacture License" on the product.
The manufacture licensing procedure of bursting disc devices shall include application, acceptance, trial production, type test, appraisal and evaluation, examination and approval, and license issuing, etc. The specific licensing procedure shall be carried out in accordance with relevant provisions.
The manufacture license conditions of bursting disc devices are detailed in Appendix C.
Article 5 In case of any one of the following conditions, the bursting disc device shall be carried out with the type test, therein, for Item (I), (II) and (III), the trial production shall be carried out prior to the type test:
(I) Applying for the Manufacture License;
(II) Prior to putting new product into production;
(III) Significant changes are made in such aspects as structure and technology of the product and influence the safety performance;
(IV) The Manufacture License is replaced;
(V) The manufacturing organization restarts the production after stopping production for over 6 months;
(VI) Problems exist in the safety performance of product.
The items and requirements of the type test of bursting disc devices are detailed in Appendix D.
Article 6 After the license application is accepted, the bursting disc device manufacturing organization shall carry out trial production in accordance with the specification and quantity required by the appraisal and evaluation and the type test, and the trial product shall select those representative ones from the bursting disc device types applying for license.
The bursting disc device manufacturing organization shall invite the bursting disc device type test organization published by the AQSIQ to do the type test on product.
Safety Technical Supervision Regulations for Bursting Disc Devices
Appendix A Terms
Appendix B Safety Technical Requirements for Bursting Disc Devices
Appendix C License Conditions for Manufacture of Bursting Disc Devices
Appendix D Requirements of Type Test of Bursting Disc Devices
Appendix E Requirements for Manufacture Supervision and Inspection of Bursting Disc Devices
Amendment 1
of
TSG ZF003-2011 Safety Technical Supervision Regulations for Bursting Disc Devices
I Amendment to the “text”
1 Article 3 is amended to:
“This Regulation specifies the basic safety requirements for the process of material, design, manufacture, inspection, installation, application and others as well as for the manufacture licensing, type test work of bursting disc devices. The technical standards of the relevant bursting disc device and the management systems of the relevant organizations and institutions shall not be less stringent than requirements of this Regulation.
The safety technical requirements for bursting disc devices are detailed in Appendix B.”
2 Article 4 is amended to:
“The manufacturing organization of bursting disc devices shall obtain the corresponding "Special Equipment Manufacture License” and “Type Test Certificate of Special Equipment”. The General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China (hereinafter referred to as "AQSIQ") shall be responsible for the acceptance, examination and approval of the manufacture license of domestic and overseas bursting disc devices.
The "Special Equipment Manufacture License” is valid for four years. The bursting disc device manufacturing organization shall adopt appropriate mode to mark the "TS" license sign, the serial number of "Special Equipment Manufacture License” and the license level on the product.
The manufacture license for bursting disc devices is classified into two levels: Class A and Class B. Class A bursting disc device manufacturers have no restrictions on the application of their products, while Class B bursting disc device manufacturers are limited to products used in Class I and Class II stationary pressure vessels, cylinders, cylinder valves, and GC2/GC3 pressure pipelines.
The manufacture licensing procedure of bursting disc devices shall include application, acceptance, trial production, type test, appraisal and evaluation, examination and approval, and license issuing, etc. The specific licensing procedure shall be carried out in accordance with relevant provisions. The manufacture license conditions of bursting disc devices are detailed in Appendix C.”
3 Article 8 is amended to:
“The bursting disc device manufacturing organization shall carry out the manufacture of products in accordance with the approved license scope and also shall accept the random inspection of the safety and quality of the bursting disc device by the special equipment type test organization.
Special equipment type test organizations shall reasonably arrange random inspections, and urge the manufacturing organizations of bursting disc devices to maintain consistent product safety and quality during the period of holding the license. The scope of random inspections shall cover the product forms under manufacture license within four years, and the inspection items and qualified indicators shall not be lower than those of type tests.”
II Amendment to “Appendix A”
1 The content of A5 is deleted and the original numbers of A6 to A15 are changed to A5 to A14 in sequence.
2 A7.2 is amended to:
“A6.2 Maximum (minimum) bursting pressure
Algebraic sum of specified bursting pressure plus performance tolerance.”
3 A7.4 is deleted.
.......
Article 1 This Regulation was formulated in accordance with "Regulations on Safety Supervision of Special Equipment" (hereinafter referred to as the "Regulations") for the purpose of ensuring the safety performance of the bursting disc devices of special equipments and strengthening the safety supervision work of bursting disc devices.
Article 2 This Regulation is applicable to the bursting disc devices used for those special equipments specified in the "Regulations".
The bursting disc device is composed of such spare parts as bursting disc and bursting disc holder. The terms related to bursting disc devices involved in this Regulation are detailed in Appendix A.
Article 3 This Regulation specifies the basic safety requirements for the process of material, design, inspection, installation, application and others as well as for the manufacture licensing, type test, supervision and inspection work of bursting disc devices. The relevant provisions of the corresponding technical standards and management systems shall not be less than requirements of this Regulation.
The safety technical requirements for bursting disc devices are detailed in Appendix B.
Article 4 The manufacturing organization of bursting disc devices shall obtain the corresponding manufacture license of special equipments. The General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China (hereinafter referred to as "AQSIQ") shall be responsible for the acceptance, examination and approval of the manufacture license of domestic and overseas bursting disc devices.
The "Special Equipment Manufacture License" is valid for four years. The bursting disc device manufacturing organization holding the manufacture license shall adopt appropriate mode to mark the "TS" license sign and the serial number of "Special Equipment Manufacture License" on the product.
The manufacture licensing procedure of bursting disc devices shall include application, acceptance, trial production, type test, appraisal and evaluation, examination and approval, and license issuing, etc. The specific licensing procedure shall be carried out in accordance with relevant provisions.
The manufacture license conditions of bursting disc devices are detailed in Appendix C.
Article 5 In case of any one of the following conditions, the bursting disc device shall be carried out with the type test, therein, for Item (I), (II) and (III), the trial production shall be carried out prior to the type test:
(I) Applying for the Manufacture License;
(II) Prior to putting new product into production;
(III) Significant changes are made in such aspects as structure and technology of the product and influence the safety performance;
(IV) The Manufacture License is replaced;
(V) The manufacturing organization restarts the production after stopping production for over 6 months;
(VI) Problems exist in the safety performance of product.
The items and requirements of the type test of bursting disc devices are detailed in Appendix D.
Article 6 After the license application is accepted, the bursting disc device manufacturing organization shall carry out trial production in accordance with the specification and quantity required by the appraisal and evaluation and the type test, and the trial product shall select those representative ones from the bursting disc device types applying for license.
The bursting disc device manufacturing organization shall invite the bursting disc device type test organization published by the AQSIQ to do the type test on product.
Contents of TSG ZF003-2011/XG1-2017
Safety Technical Supervision Regulations for Bursting Disc Devices
Appendix A Terms
Appendix B Safety Technical Requirements for Bursting Disc Devices
Appendix C License Conditions for Manufacture of Bursting Disc Devices
Appendix D Requirements of Type Test of Bursting Disc Devices
Appendix E Requirements for Manufacture Supervision and Inspection of Bursting Disc Devices
